1. localhorst

    PoE+ IEEE802.3at for several Axis PTZ cameras

    Hello Community, I purchased second-hand following Axis cameras: P5414-E P5624-E P5532 Unfortunately none of the above is working when powered with PoE. As a PoE+ Switch I tested with: TP-Link TL-SG1005P Netgear GS308PP I was never able to obtain an Ethernet link. So I suspect the problem...
  2. saltwater

    What a great idea - garage roller door - wireless reed switch and door hinge

    I installed a wireless alarm system and have wireless reed switches on every entry/exit door except my garage roller door. When I purchased the system, many months ago, I was told the system did not have a garage roller door reed switch, period. As I now know, that was the knowledge base...
  3. R

    Fanless PoE Switch

    We currently have a Trendnet TPE-S160 PoE switch which has a fan that is always running. I considered replacing the fan with a quieter model but I would prefer the replace it with no fan at all. I did quite a big of research but couldn't find anything great. It will go into a rack so it should...
  4. amrogers3

    Calculating bandwidth requirement for switch

    For a camera I am planning to buy, I found the following specs. Main stream: 3840 × 2160 @(1–25/30 fps) Sub stream: 704 × 576@1–25 fps/704 × 480@1–30 fps Third stream: 1920 × 1080 @ (1–25/30 fps) I would like to have 8 channels live streaming to a TV. The sub stream has terrible resolution...
  5. S

    Dahua Switch PoE all leds shining

    Hey, can you give some advice. My dahua switch poe with 8 ports last night out of work. When i tried to find out what happened. I saw that all ports led indicators (pawer and link) shining when turn on switch, without connecting any ip cameras. Can anybody help me with this?
  6. J

    Cannot access my switch on a second nic

    Here is my setup: ISP provided modem/switch (In bridge mode) ------> Asus Router ----> Desktop PC (with two nics) -----> Cisco Switch I have IP Cameras attached to the switch, and I do not want the cameras to have internet access (Chinese Cameras) I am 100% sure that everything is on the same...
  7. I

    What NVR for Dahua TiOC cameras (ideally with live backup to Synology NAS)

    Hi all, I have six cameras, two on the main house and four on an outbuilding. Mix of: Dahua DH-IPC-HDW3549H-AS-PV WizSense TiOC Grey Outdoor HD PoE Turret IP Camera w/ 2.8mm Lens, 30m Full Colour, Audio & Alarm (5 MP) Dahua DH-IPC-HFW3549T1-AS-PV WizSense TiOC Outdoor HD PoE Bullet IP Camera...
  8. AveryFreeman

    Using POE Texas injectors with VLANs

    Hey, so I've never tried using a POE injector with VLANs before. Has anyone tried using POE injectors on a network using VLAN encapsulation? And if so, how'd that go? Have a friend with lots of streaming devices, network is starting to have latency issues. I'm pretty sure he'll have to get...
  9. A

    NVR4216-16P-I internal switch adresses

    Hello, I have most on my cameras connected to 192.x.x.0 subnet, and 6 of them connected to NVR's internal PoE switch on 10.x.x.0. I want to change their adresses to ones from 192.x.x.0. Should I change switch adress in NETWORK>SWITCH, and then change camera adresses from CAMERA>REMOTE DEVICE, or...
  10. saltwater

    Physical switches and VLANs

    I'm at the stage now where I'm planning out my network for my house currently under construction. I am going the UniFi way of doing things, will get an Edge Router X, and for my setup, I'll have two switches, one UniFi 16 port PoE+ switch and for the other a UniFi 16-24 port non-PoE switch...
  11. majektom

    Dahua NVR5232-16P-4KS2E built-in PoE switch doesn't act like a switch

    Hello good and helpful people, I have a Dahua NVR5232-16P-4KS2E recorder which has a built-in 16 port PoE switch. Apart from IP cameras, I want to connect to the switch Dahua VTO and Dahua VTH. The problem that I have is that when I connect the VTO and the VTH to NVR switch's ports, they don't...
  12. rifaazeem

    Geovision ADR1300- IP Camera not working through switch/router ports

    Hi all, If anyone could assist me on this issue will be much appreciated. situation cable from camera to Rack side ( aprox 120 meters) but it has separate power source nearby the camera, when connecting directly to the laptop its working and pinging without even 1 drop out. but when i connect...
  13. MrNaz

    Dahua NVR with switch

    Hi all I am about to deploy my first Dahua system and I have a few questions about how they work. I will be using the NVR 4416. If I have several cameras in a cluster that are a long way off, can I put a small switch near the cameras, so that I only have to run one long cable to the switch and...
  14. S

    Newbie: Recommendation for Managed PoE Switch

    Hi All, New visitor to IPCT! I'm planning to install a few IP/PoE cams at my home. I'm planning to connect all the cams in their own VLAN so that I can filter out-bound internet traffic from the cameras (based on my preliminary knowledge). My understanding is that this can be achieved by a...
  15. A

    Hikvision DS-7732NI-K4/16P NVR 17+ cameras

    Hi all, I'm having a right time with a new Hikvision DS-7732NI-K4/16P NVR and I'm struggling to solve this one in a way I like. User has 20 cameras, all POE Hikvision which I've installed. Plug each one-by-one into the 16 port POE switch on back of the NVR, so it does it's auto setup...
  16. S

    Hikvision Cameras work on main switch, but not on remote one

    I just purchased 2 more Hikvision DS-2CD2042WD-I 4MP HD cameras to match the one I have working already. I plugged them into my main, 24 port switch downstairs and configured each of them with unique IP addresses. I am also using injectors to power these POE. I was able to see them fine on both...
  17. TJH132

    Managed vs. unmanaged PoE switch

    I currently use an unmanaged 8-port PoE switch (4 powered, 4 un-powered) as part of my network. It was a real plug and play set-up and has been completely reliable without any intervention. But now I'm looking to add cameras and devices and need more ports. There's definitely a point where...
  18. P

    New POE switch; Can I use it for my regular networking too?

    I just bought some additional cameras from Andy and got a good HP from my work (I5-8400, 16GB RAM, 1TB HDD), I will be purchasing the purple WD drive in the near future but need a swtich. Attached is my current need and future need. I am not networking savvy, so I was hoping to buy an unmanaged...
  19. I

    Recommendations of a POE switch(4+ port) for home use

    Hi guys, as IP seems the standard to go and POE becomes a neat way to power the devices up, I wonder what POE switch for a home scenario you can recommend? Requirements: 4+ POE ports (at least 802.3af support?) - better 8 What standards should be supported? Are 15W output per port enough...
  20. S

    Cams work directly to router -- not through switch?

    Hi, I picked up two inexpensive IP cameras to try out last week. They each have a POE injector, and I tested both of them connected to my router and both worked fine (simultaneously). I don't have enough ports on my router to dedicate a port to each camera (and I may add more cameras in the...
  21. A

    Poe & Poe+ switch

    Hey, I’m considering getting one SD49225T-HN (which requires poe+) and 3 turrets (running on standard poe). The plan is to use these with a non-Poe nvr and therefore trying to figure out options on How to accomplish this. I plan to use these cameras in my summer house which is basically shut...
  22. B

    Swap out IP Camera on Hikvision NVR

    I want to swap out 2 cameras on a Hikvision NVR. The new cameras are Hikvision cameras. Can I just look up the info on the existing camera and put that IP Address and info into the new camera and swap them out?
  23. N

    Dual NVR Switching question

    Hi I have two Hikvision CCTV NVRs each has a HDMi & Lan output and I wish to view both NVrs on one HDTV, however I want it to auto switch between the two sources. Can anyone recommend a way to do this? Thanks for looking.
  24. Mike K

    Network Configuration with 2 Switches?

    Here is my situation: If I have two switches, one in each of two buildings connected with a single fiber trunk cable & Each switch is "managed", but the manufactures are different & Each switch has its own firmware to handle device/network configuration assignments & Both switches are VLAN...
  25. chrisimmanuel

    Case about connecting 8 IP Cams thru a POE Switch

    Hi Folks, I have an installation case that i need to solve, 1. i need to install 8 IP Camera 2. We need to have two NVR on a separate room 3. first NVR will only show channel 1-4 and the second NVR will only show 1-8 my question is, I want to use this scenario by using a separate POE switch...
  26. Mike K

    Witch Switch

    I'm down to selecting one of two switches for my system. The two choices are between these: NETGEAR ProSAFE GS110TP 8-Port PoE Gigabit Smart Managed Switch with 2 Gigabit SFP Ports 53w (GS110TP-200NAS) Or: UniFi Switch 8 (150W) Both of these look to have the same features with 8 POE...
  27. Mike K

    Tech support for the UniFi Switch?

    This POE Switch looks very good with 150W total power and other features: https://www.ubnt.com/unifi-switching/unifi-switch-8-150w/ However, I have searched high and low for a contact to the company so I can talk to someone about the unit befor I purchase it, and im not finding any available...
  28. N

    POE Switch Question

    Hello, I am interested in getting 6-8 Hikvision cameras and I am looking for a good switch to power them. Is the NETGEAR ProSAFE JGS516PE 16-Port Gigabit Rackmount PoE a good option? Thanks.
  29. N

    Help with network switch selection for my BI build

    Could someone help me in identifying what type of network switch I'll need for my planned setup. I plan to run BI on a Win 10 Pro machine Up to 12-15 4MP+ cameras eventually over time All camera power to be POE powered from the switch 1 or 2 PTZ Zoom cameras Cameras would record to disc...
  30. B

    Need Some Recomendations on QUIET (10-16) PoE Switch

    Hey guys I hope someone can recommend a QUIET PoE switch (needs to be rack mountable) I have a Buffalo 16 port PoE Switch - BS-GS2016P Here is the problem - It is a great switch, but the fans run non stop and they are loud. I think that part of the problem is because when you get into 16...