DS-2CD2043G0-I Help!

B

baha30

n3wb
Dec 14, 2018
13
0
uzb
Good day! help is needed
There is a DS-2CD2043G0-I SF.Version v5.51_180314 / camera
After the voltage drop flew Software
Found this version but it does not flash
gives an error message

There are other less IPC_G1_EN_STD_5.5.4_171206_EN_ONLY
it goes well
but SADPTool does not see the camera
here log
 

Attachments

baha30 said:
There are other less IPC_G1_EN_STD_5.5.4_171206_EN_ONLY
it goes well
but SADPTool does not see the camera
Click to expand...
Maybe the wrong firmware - even though it was accepted.

I think this should be the firmware for the camera :
DOWNLOAD EU PORTAL
But is the camera a China region camera?
Code: 
[PACK][DBG_INFO][src/firm_unpack_lib.c][firm_pack_decode][183]:iPackIdx=0,iPackF
lg=0x00650100,iPlatform=101,iDevMajor=111,iDevMinor=111,iLanguage=2

And this could be bad, it may mean the hardware is not clear to the firmware :
Code: 
booting from pri part...
load kernel...
Get dtb failed
 
i download this version v5.5.51_180314
but this ver not load in camera

U-Boot 3.1.6-371476 (May 11 2018-21:35:18)
boards:378780
Boot From: NAND 2048 RC BCH 6bit
SYS_CONFIG: 0x00070053 POC: 001
Cortex freq: 816000000
ENET freq: 50000000
iDSP freq: 348000000
Dram freq: 840000000
Core freq: 360000000
AHB freq: 180000000
APB freq: 90000000
UART freq: 24000000
SD freq: 50000000
SDXC freq: 50000000
dev_model:DS-2CD2043G0-I
[Uboot] In release mode!
Hit Ctrl+u to stop autoboot: 1
HKVS # гзвфеу
cmd 'гзвфеу' is not supported.
HKVS # update
'update' is a ambiguous command! Exec the shortest command
Get dtb failed
Starting udev: [ OK ]
create static device nodes under /dev dir
modprobe: chdir(): No such file or directory
iptables v1.4.18: can't initialize iptables table `filter': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
>>>run pre_app_hook
find net_node, loop : 1
[ INFO][MIN]TFTP: TFTP from server 192.0.0.128
[ INFO][MIN]TFTP: Filename: 'digicap.dav'
tftp: falling back to blocksize 512
##############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################tftp: timeout
[ INFO][MIN]TFTP: Download File [FAIL] error: tftp.
!!!!! UPDATE FAIL !!!!!

BusyBox v1.2.1 Protect Shell (psh)
Enter 'help' for a list of davinci system commands.
 
alastairstevenson said:
Get dtb failed
Click to expand...
On other brands, if the dtb (Device Tree Block) is corrupted or not available, the kernel may not have the details to be able to address the hardware correctly.
That is usually a fatal error. The dtb lists the hardware elements against the addresses that they are accessible on, as well as other parameters.
But I don't know how significant it is on your model of camera.

baha30 said:
where else can I download?
Click to expand...
This is the same firmware, but some newer versions : ftp://ftp.hikvision.ru/02.%202-line%20cameras/4.%20G1%20platform%20-%20DS-2CD2XX5%202XX3G0/

baha30 said:
which models are suitable
Click to expand...
The release note for the firmware here DOWNLOAD EU PORTAL does include your camera model.
 
i download relase
5.5.51
5.5.61
5.5.80
5.5.82
all not update

U-Boot 3.1.6-371476 (May 11 2018-21:35:18)
boards:378780
Boot From: NAND 2048 RC BCH 6bit
SYS_CONFIG: 0x00070053 POC: 001
Cortex freq: 816000000
ENET freq: 50000000
iDSP freq: 348000000
Dram freq: 840000000
Core freq: 360000000
AHB freq: 180000000
APB freq: 90000000
UART freq: 24000000
SD freq: 50000000
SDXC freq: 50000000
dev_model:DS-2CD2043G0-I
[Uboot] In release mode!
Hit Ctrl+u to stop autoboot: 1
HKVS # erase
partition needs to be specified!
HKVS # update
'update' is a ambiguous command! Exec the shortest command
Get dtb failed
Starting udev: [ OK ]
create static device nodes under /dev dir
modprobe: chdir(): No such file or directory
iptables v1.4.18: can't initialize iptables table `filter': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
>>>run pre_app_hook
find net_node, loop : 1
[ INFO][MIN]TFTP: TFTP from server 192.0.0.128
[ INFO][MIN]TFTP: Filename: 'digicap.dav'
tftp: falling back to blocksize 512
##############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################tftp: timeout
[ INFO][MIN]TFTP: Download File [FAIL] error: tftp.
!!!!! UPDATE FAIL !!!!!

BusyBox v1.2.1 Protect Shell (psh)
Enter 'help' for a list of davinci system commands.
 
what is the problem
I do not know :idk::idk::idk::screwy::screwy::screwy::screwy:

may need chinese firmware?
but where to download chinese firmware?
 
Last edited:
baha30 said:
what is the problem
Click to expand...
baha30 said:
########################################tftp: timeout
[ INFO][MIN]TFTP: Download File [FAIL] error: tftp.
Click to expand...
I think that is the problem - the timeout. The file download is incomplete.

If you are using the Hikvision tftp updater - it does not work for firmware files larger than 32MB.
These are 34MB.

As you are using the bootloader 'update' command, you can use a normal tftp server to get round that problem.
For example, the 32-bit jounin one from here works well : TFTP server
 
baha30 said:
update from TFTP server (update ok)
Click to expand...
Looking good (apart from the trashed primary configuration data) until the problem initialising the DSP, in both the log files.
I'm not sure what the cause of that could be.

Even though the DSP is part of the SoC, not in the sensor, it would be worth checking / re-seating the flex cable that connects the sensor to the main board.
A long shot, but easy enough to do.

And I'm still wondering how significant "Get dtb failed" is.
But it seems happy with the rest of the hardware.
 
baha30 said:
Should I replace?
Click to expand...

Hello, have You resolved this problem?

I have the same camera model DS-2CD2043G0-I and the same problem: camera doesn't appear in SADP and in console after boot showing this logs:


Code: 
armlib]start_dsp 171:>>>>>>>>>>>>>>>>>  Start dsp core timeOut, bootInfo=5  <<<<<<<<<<<<<
davinci receive cmd_query_davinci_param.
S: cmd_query_davinci_param

[armlib]start_dsp 171:>>>>>>>>>>>>>>>>>  Start dsp core timeOut, bootInfo=5  <<<<<<<<<<<<<
davinci receive cmd_query_davinci_param.
S: cmd_query_davinci_param

[armlib]start_dsp 171:>>>>>>>>>>>>>>>>>  Start dsp core timeOut, bootInfo=5  <<<<<<<<<<<<<
davinci receive cmd_query_davinci_param.
S: cmd_query_davinci_param

[armlib]start_dsp 171:>>>>>>>>>>>>>>>>>  Start dsp core timeOut, bootInfo=5  <<<<<<<<<<<<<
davinci receive cmd_query_davinci_param.
S: cmd_query_davinci_param
 
You must log in or register to reply here.
Top Bottom