Can't Add JVC VNH257VPU

J

JesseF

n3wb
Jan 2, 2017
10
1
I have read through a lot of the threads on here and still can't seem to figure out my issue. I am attempting to add a camera to my BI system. I can access the camera on my laptop by visiting the cameras IP address and putting in the credentials. When I attempt to add the camera to BI I put click the find/inspect button and receive the below info. When I click OK to save the camera (like I have done on other cameras) I get a RTSP: 404 Not Found.

I am running a PC based system with Windows 10.
I have my computer plugged directly into the router.
Ther router running to a POE switch and the cameras hooked into the POE.
I have 11 other mixed brandes (Dahua, Hikvision) running on the system and have set them up the same way.

Any help would be appreciated.

Here is the find/inspect results:

Opening 192.168.1.61 port 80...
HTTP Get / request...
OK
ONVIF GetSystemDateAndTime
2018-02-10T20:39:15.000Z
Requesting device information...
Manufacturer: JVC KENWOOD
Model: VN-H257VP
FirmwareVersion: 6.01.006
GetCapabilities...
Querying services
Has Imaging services: /onvif/imaging_service
Has media services: /onvif/media_service
Has RTP_RTSP_TCP, requesting profiles
Has Event services: /onvif/event_service
Has WSPullPointSupport
RelayOutputs: 2
InputConnectors: 2
Has Device IO services: /onvif/deviceio_service
AudioOutputs: 1
Has PTZ service: /onvif/ptz_service
Checking for common cameras...
Foscam FI86xx/98xx compatible?
Foscam FI89xx compatible?
Foscam FI9821 V2 compatible?
Foscam FI9821 media port compatible?
RTSP port open?
RTSP port detected!
Done

 
Type your http like this: 192.168.1.61:80

Then hit inspect see what that does.
 
Putting :80 at then end came back with the same results. I can post here if you would like but comparing them it looks like the only difference is the date and time.
 
JesseF said:
Putting :80 at then end came back with the same results. I can post here if you would like but comparing them it looks like the only difference is the date and time.
Click to expand...
What is the rtsp port set to in your camera?
 
When you say in your camera do you mean when accessing it through a browser and looking at the settings? If so I have attached a screenshot of the settings but dont see anything that says RTSP. If you mean in BI then it is 554
 

Attachments

  • CaptureJVC.PNG
    CaptureJVC.PNG
    36.2 KB · Views: 3
JesseF said:
When you say in your camera do you mean when accessing it through a browser and looking at the settings? If so I have attached a screenshot of the settings but dont see anything that says RTSP. If you mean in BI then it is 554
Click to expand...
ok, post the blue iris video>configuration settings as well..
 
Under JVC there are only 6 cameras. I tried them all with no luck. If this helps here are the two pieces of information that post you referenced asked to check. Thank you again.
 

Attachments

  • JVC1.PNG
    JVC1.PNG
    10.8 KB · Views: 5
Would the additional information I posted help anyone suggest another option? Thanks for the time.
 
I did try putting the string rtsp://192.168.1.61/ONVIF/Streaming/channels/0 into the path field under Video but that didn't work. I tried it on the generic camera after hitting find/inspect as well as on each JVC camera listed (which is 6). Some of the JVC cameras came back with 400 bad request while the others came back with RTSP 404 Not Found.
 
You must log in or register to reply here.
Top Bottom