Dahua DHI-NVR4108HS-4KS2 - Yellow Motion bar

K

kuzco

Young grasshopper
Jan 17, 2020
92
5
Germany
Hello,
I have several Dahua IPC connected to my Dahua NVR:

IPC:
1. IPC-T5442TM (2.840.15OG00D.0.R,2022-08-18)
2. IPC-HDW4631C-A (2.460.GP01.16.R,2017-09-04)
3. IPC-HDW6238X (2.600.0000.2.R,2017-03-18)
4. I51DF (V5.5.801 build 220214) (Annke C500 with HikVision FW)
IPC 2 and 3 are chinese models.

NVR:
DHI-NVR4108HS-4KS2 (V4.001.0000005.1, Build Date: 13-07-2021)

So far so good.

For IPC 1-3 I have defined under /Event/VideoDetection an area.
For IPC No. 1 (T5442) and 3 (6238X) I can see on the NRV under "Search" a "yellow" bar, but not for IPC 2 (4631).
Is there anything I have missed to configure ?

And yes, I will change IPC 2 and 3 sometimes to "orginal" IPC.

KR
roland
 
Did you set the schedule in the storage / schedule / cog (gear) / select motion ? Easy to miss sometimes.
 
jmcu said:
Did you set the schedule in the storage / schedule / cog (gear) / select motion ? Easy to miss sometimes.
Click to expand...
Hello, thanks for your reply.
Under /Storage/Sechedule I do have only "Recored, Snapshot, Holiday Schedule".

Before I have configured and added the NVR, I have used only ftp as a target to store after motion-detection.
00:00-06:00 - only record
06:00-22:00 - only snapshot
22:00-06:00 - only record

In addition to the NVR I am still using the ftp target. So, from my point of view the configuration is fine.
For all other IPC I am using record only for the whole day.

KR
roland
 
kuzco said:
Hello,
I have several Dahua IPC connected to my Dahua NVR:

IPC:
1. IPC-T5442TM (2.840.15OG00D.0.R,2022-08-18)
2. IPC-HDW4631C-A (2.460.GP01.16.R,2017-09-04)
3. IPC-HDW6238X (2.600.0000.2.R,2017-03-18)
4. I51DF (V5.5.801 build 220214) (Annke C500 with HikVision FW)
IPC 2 and 3 are chinese models.

NVR:
DHI-NVR4108HS-4KS2 (V4.001.0000005.1, Build Date: 13-07-2021)

So far so good.

For IPC 1-3 I have defined under /Event/VideoDetection an area.
For IPC No. 1 (T5442) and 3 (6238X) I can see on the NRV under "Search" a "yellow" bar, but not for IPC 2 (4631).
Is there anything I have missed to configure ?

And yes, I will change IPC 2 and 3 sometimes to "orginal" IPC.

KR
roland
Click to expand...
Hi,
Sorry to Hijack this thread. But I have a question about the Annke C500. Which HikVision FW did you use? Thanks in advance...
 
I had a similar problem with my 5442 and discovered that after unchecking the motion detection that settings for threshold and sensitivity go to zero. When you rechecking motion detection, I had to reset the threshold and sensitivity, but all other settings remained.
 
kuzco said:
Please see inside my question.
It is V5.5.801 build 220214.
Click to expand...
I am sorry, I guess that I didn't phrase my question properly. Which Hikvision Camera model is this firmware for? I have seen comments where people flashed the firmware targeted for IPC_E7S_EN_STD and they ended with lower resolution. If you can share what Hikvision equivalent model you used, it would be of great help to me since I have 8 C500 cameras that I need to upgrade/migrate.
 
yabdali said:
I am sorry, I guess that I didn't phrase my question properly. Which Hikvision Camera model is this firmware for? I have seen comments where people flashed the firmware targeted for IPC_E7S_EN_STD and they ended with lower resolution. If you can share what Hikvision equivalent model you used, it would be of great help to me since I have 8 C500 cameras that I need to upgrade/migrate.
Click to expand...
It was E7-DS-2CD1x43G0E-I - IPC_E7 and not IPCH_E7/IPCH_HL_E7.
 
kuzco said:
It was E7-DS-2CD1x43G0E-I - IPC_E7 and not IPCH_E7/IPCH_HL_E7.
Click to expand...

Thanks again. When I check DS-2CD1x43G0E-I models specs I see all of them referring to 4MP cameras and not 5MP. Can you confirm if your camera resolution was downgraded to 4MP after your flashed Hikvision firmware?
 

Attachments

  • hikvision4mp.png
    hikvision4mp.png
    43.7 KB · Views: 7
You must log in or register to reply here.
Top Bottom