Dahua DHI-NVR4108HS-4KS2 - Yellow Motion bar

kuzco

Young grasshopper
Joined
Jan 17, 2020
Messages
87
Reaction score
5
Location
Germany
Hello,
I have several Dahua IPC connected to my Dahua NVR:

IPC:
1. IPC-T5442TM (2.840.15OG00D.0.R,2022-08-18)
2. IPC-HDW4631C-A (2.460.GP01.16.R,2017-09-04)
3. IPC-HDW6238X (2.600.0000.2.R,2017-03-18)
4. I51DF (V5.5.801 build 220214) (Annke C500 with HikVision FW)
IPC 2 and 3 are chinese models.

NVR:
DHI-NVR4108HS-4KS2 (V4.001.0000005.1, Build Date: 13-07-2021)

So far so good.

For IPC 1-3 I have defined under /Event/VideoDetection an area.
For IPC No. 1 (T5442) and 3 (6238X) I can see on the NRV under "Search" a "yellow" bar, but not for IPC 2 (4631).
Is there anything I have missed to configure ?

And yes, I will change IPC 2 and 3 sometimes to "orginal" IPC.

KR
roland
 

jmcu

Known around here
Joined
Jul 5, 2016
Messages
453
Reaction score
680
Location
New York
Did you set the schedule in the storage / schedule / cog (gear) / select motion ? Easy to miss sometimes.
 

kuzco

Young grasshopper
Joined
Jan 17, 2020
Messages
87
Reaction score
5
Location
Germany
Did you set the schedule in the storage / schedule / cog (gear) / select motion ? Easy to miss sometimes.
Hello, thanks for your reply.
Under /Storage/Sechedule I do have only "Recored, Snapshot, Holiday Schedule".

Before I have configured and added the NVR, I have used only ftp as a target to store after motion-detection.
00:00-06:00 - only record
06:00-22:00 - only snapshot
22:00-06:00 - only record

In addition to the NVR I am still using the ftp target. So, from my point of view the configuration is fine.
For all other IPC I am using record only for the whole day.

KR
roland
 

yabdali

n3wb
Joined
Dec 4, 2019
Messages
7
Reaction score
0
Location
Muscat
Hello,
I have several Dahua IPC connected to my Dahua NVR:

IPC:
1. IPC-T5442TM (2.840.15OG00D.0.R,2022-08-18)
2. IPC-HDW4631C-A (2.460.GP01.16.R,2017-09-04)
3. IPC-HDW6238X (2.600.0000.2.R,2017-03-18)
4. I51DF (V5.5.801 build 220214) (Annke C500 with HikVision FW)
IPC 2 and 3 are chinese models.

NVR:
DHI-NVR4108HS-4KS2 (V4.001.0000005.1, Build Date: 13-07-2021)

So far so good.

For IPC 1-3 I have defined under /Event/VideoDetection an area.
For IPC No. 1 (T5442) and 3 (6238X) I can see on the NRV under "Search" a "yellow" bar, but not for IPC 2 (4631).
Is there anything I have missed to configure ?

And yes, I will change IPC 2 and 3 sometimes to "orginal" IPC.

KR
roland
Hi,
Sorry to Hijack this thread. But I have a question about the Annke C500. Which HikVision FW did you use? Thanks in advance...
 

Old Larry

Getting the hang of it
Joined
Jun 17, 2019
Messages
19
Reaction score
118
Location
Virginia
I had a similar problem with my 5442 and discovered that after unchecking the motion detection that settings for threshold and sensitivity go to zero. When you rechecking motion detection, I had to reset the threshold and sensitivity, but all other settings remained.
 

kuzco

Young grasshopper
Joined
Jan 17, 2020
Messages
87
Reaction score
5
Location
Germany
Hi,
Sorry to Hijack this thread. But I have a question about the Annke C500. Which HikVision FW did you use? Thanks in advance...
Please see inside my question.
It is V5.5.801 build 220214.
 

yabdali

n3wb
Joined
Dec 4, 2019
Messages
7
Reaction score
0
Location
Muscat
Please see inside my question.
It is V5.5.801 build 220214.
I am sorry, I guess that I didn't phrase my question properly. Which Hikvision Camera model is this firmware for? I have seen comments where people flashed the firmware targeted for IPC_E7S_EN_STD and they ended with lower resolution. If you can share what Hikvision equivalent model you used, it would be of great help to me since I have 8 C500 cameras that I need to upgrade/migrate.
 

kuzco

Young grasshopper
Joined
Jan 17, 2020
Messages
87
Reaction score
5
Location
Germany
I am sorry, I guess that I didn't phrase my question properly. Which Hikvision Camera model is this firmware for? I have seen comments where people flashed the firmware targeted for IPC_E7S_EN_STD and they ended with lower resolution. If you can share what Hikvision equivalent model you used, it would be of great help to me since I have 8 C500 cameras that I need to upgrade/migrate.
It was E7-DS-2CD1x43G0E-I - IPC_E7 and not IPCH_E7/IPCH_HL_E7.
 

yabdali

n3wb
Joined
Dec 4, 2019
Messages
7
Reaction score
0
Location
Muscat
It was E7-DS-2CD1x43G0E-I - IPC_E7 and not IPCH_E7/IPCH_HL_E7.
Thanks again. When I check DS-2CD1x43G0E-I models specs I see all of them referring to 4MP cameras and not 5MP. Can you confirm if your camera resolution was downgraded to 4MP after your flashed Hikvision firmware?
 

Attachments

kuzco

Young grasshopper
Joined
Jan 17, 2020
Messages
87
Reaction score
5
Location
Germany
Good question. But in the meantime I have already sold the camera. So, I have no chance to verify.
 
Top