Missing recording after rebooting & camera not viewing properly | DS-9632NI-I8

S

shamtph

n3wb
Oct 25, 2022
5
2
Malaysia
Dear all,

I have 2 issues here:

1.I am having issue on my recording. Every time it reboots randomly or manually reboot, the recording gone missing without an error.
I have not done self test on HDD yet, but anyone have a clue on what are the issue?

If the HDD is having issue, how do i know which of the 3 HDD inside NVR having issue?

2. Some cameras didn't show properly, but when i double click on that camera, it shows the view normally.

I will give some screenshot in the attachment.

Here is my NVR specification:

Model: DS-9632NI-I8

Firmware Version: V4.1.70 build 181114

No of camera installed: 32 channels

No of HDD: 3 X 4TB WD HDD

Any help would be appreciated. Thanks!
 

Attachments

  • 1.jpg
    1.jpg
    207.7 KB · Views: 8
shamtph said:
.I am having issue on my recording. Every time it reboots randomly or manually reboot, the recording gone missing without an error.
I have not done self test on HDD yet, but anyone have a clue on what are the issue?
Click to expand...
Have you tried using the 'Rebuild Video files' button?

1666776015110.png
 
shamtph said:
Dear all,

I have 2 issues here:

1.I am having issue on my recording. Every time it reboots randomly or manually reboot, the recording gone missing without an error.
I have not done self test on HDD yet, but anyone have a clue on what are the issue?

If the HDD is having issue, how do i know which of the 3 HDD inside NVR having issue?

2. Some cameras didn't show properly, but when i double click on that camera, it shows the view normally.

I will give some screenshot in the attachment.

Here is my NVR specification:

Model: DS-9632NI-I8

Firmware Version: V4.1.70 build 181114

No of camera installed: 32 channels

No of HDD: 3 X 4TB WD HDD

Any help would be appreciated. Thanks!
Click to expand...
As an employee of a Hikvision dealer, I will tell you what is wrong to help you out:
Your firmware is out of date and the newer versions of hik-connect can cause the unit to reboot randomly.
It needs to be updated so you don't experience the issues you are experiencing.


Also, all functions for the NVR should be administered directly from the NVR either by at the machine or its admin login from its ip address and not thru IVMS.
 
Last edited:
alastairstevenson said:
In a RAID configuration as shown in the screenshot, how should a recorded data rebuild (not a RAID rebuild) be initiated?
Click to expand...
It doesn't look like the correct screen, like its from ivms instead of the NVR
You have to do all of this at the NVR.

You add a drive as a hot spare, then rebuild. I use an external esata hdd for that until I change the failed drive that is listed in physical disk.

If you have good drives and have to rebuild, you have to use a hot spare as well.

on page 130 of this manual, you will see what I am talking about:

BTW I avoid raids. If they need a mirror, I sell them a 2nd nvr, and only one goes online for remote viewing, the other is a backup that insures it from all NVR based failures.
 
Last edited:
It's not about a RAID rebuild, I was asking about the data rebuild in a RAID system.
If a RAID rebuild was needed there would be log entries complaining about the RAID status.
 
tech_junkie said:
As an employee of a Hikvision dealer, I will tell you what is wrong to help you out:
Your firmware is out of date and the newer versions of hik-connect can cause the unit to reboot randomly.
It needs to be updated so you don't experience the issues you are experiencing.


Also, all functions for the NVR should be administered directly from the NVR either by at the machine or its admin login from its ip address and not thru IVMS.
Click to expand...

Newer version of hik-connect? is it my IVMS software?

If i want to update firmware, will it be any data lost?
 
You must log in or register to reply here.
Top Bottom