HiKvision DS-7616 and Sricam 1004/05 or wanscam ptz

[rebelbah]

Just bought a new DS-7616 and trying to connect some older cameras such as Sricam 1004/05 or wanscam ptz(indoor), I'm so far unable to get either of them to connect to the NVR, anyone have the same issue, if so how did you resolve it.
Also have a few other 1mp or better non Hikvision cameras that i have gotten connected but unable to control the motion settings(dont want to use continuous recording)


trying something else, Blue iris is way to power hungry, from what i have and running 5) 2mp or less cameras, it will take a $1000-$1500 computer to handle 12 to 16 cameras(3mp average)

 

[fenderman]

trying something else, Blue iris is way to power hungry, from what i have and running 5) 2mp or less cameras, it will take a $1000-$1500 computer to handle 12 to 16 cameras(3mp average)

You are misinformed. You can run your load on 200 dollar computer. You can run 12-16 3mp cameras on a 300-500 pc. There are many threads that discuss this.

 

[rebelbah]

You are misinformed. You can run your load on 200 dollar computer. You can run 12-16 3mp cameras on a 300-500 pc. There are many threads that discuss this.

Well I have a quad core 1.8ghz with 8gb ram windows 10 64bit and it's running at 87% or higher 90% of the time with a SSDrive

I'll have to look around to and see what they doing or not doing different

 

[fenderman]

Well I have a quad core 1.8ghz with 8gb ram windows 10 64bit and it's running at 87% or higher 90% of the time with a SSDrive

I'll have to look around to and see what they doing or not doing different

What EXACT processor do you have? The words quad core and 1.8ghz mean nothing. What cameras and what resolution and frame rate?
You need to set direct to disk recording. record tab>file format. Each camera. This does not work in the demo mode.

 

[rebelbah]

Celeron N2930 processor
1 2mp camera set to 1280*720 30fps
1 1.3mp set to 1280*720 30fps
1 1mp set to 1280*720 30fps
1 1mp set to 1280*720 20fps
1 640*480 20fps

i have a licensed copy of Blue Irus

 

[fenderman]

Celeron N2930 processor
1 2mp camera set to 1280*720 30fps
1 1.3mp set to 1280*720 30fps
1 1mp set to 1280*720 30fps
1 1mp set to 1280*720 20fps
1 640*480 20fps

i have a licensed copy of Blue Irus

The Celeron N2930 is a very weak processor.
http://www.cpubenchmark.net/cpu.php?cpu=Intel+Celeron+N2930+@+1.83GHz
Have you enabled direct to disk for each camera? This is extremely important.
Have you enabled hardware acceleration?
Also, lower the frame rates in the cameras themselves to 15. 30fps is extreme overkill.

 

[Lestlie]

hello, I know Wanscam JW0005, this cameras do not support NVR, if you need it connect to NVR, you need go for HW series. You can go to their alibaba:www.wanscam.en.alibaba.com

 

[Del Boy]

hello, I know Wanscam JW0005, this cameras do not support NVR, if you need it connect to NVR, you need go for HW series. You can go to their alibaba:www.wanscam.en.alibaba.com

Probably but this is terrible advice. If you have a Hikvision NVR then stick with Hikvision cameras. If you want to save money then don't get a Hikvision NVR.

 

[rebelbah]

I know your response above was directly to Lestlie, but in my case i already have some other cameras other then HiKvision, will be purchasing some HiKvision dome and bullet cameras to add to my list

 

[hmjgriffon]

Blue iris, use any camera you want

Sent from my Nexus 6P using Tapatalk

 

[nayr]

Blue iris, use any camera you want

Sent from my Nexus 6P using Tapatalk

why u digging up dead threads? last reply was: 7-18-2016..

noobs and tapatalk, sigh..

 

[hmjgriffon]

why u digging up dead threads? last reply was: 7-18-2016..

noobs and tapatalk, sigh..

Yeah I blame them, it was in my feed like it was recent