My cctv system
Hikvision HiLook NVR-216MH-C/16P - network video recorder - second hand
Hikvision DS-2CD2T42WD-i5 - poe camera x 2 - second hand
Hikvision DS-2CD2347G2-LU - poe camera x 4 - second hand
Annke AN-i51EM - poe camera - new
Annke AP-i51DS - poe camera - new
Annke AP-i91DM - poe camera - new
12v power supply
Win 11 PC
The 4 x Hikvision DS-2CD2347G2-LU, Annke AN-i51EM and Annke AP-i51DS cameras activated using SADP and Chrome Browser, and are working fine when connected to the Hikvision NVR.
The Annke AP-i91DM camera activated using SADP and Chrome Browser, and can be viewed through the browser, with the Annke Live View, and configurations adjusted as needed. But will not connect, when plugged in, to the Hikvision HiLook NVR.
The 2 x Hikvision DS-2CD2T42WD-i5 cameras are already active, and I am able to adjust their IP range, using the 12345 password, with an on-screen confirmation, 'Parameters modification completed' in SADP, so I am assuming the password is good ! They will open Chrome Browser, but, 'This site can't be reached' 'refused to connect' is displayed across the browser page. These camera's will not connect when plugged into the Hikvision HiLook NVR either. Enable DCHP is greyed out and not available in SADP. The gateway and subnet are in the correct range - 192.168.0.1 - 192.168.0.100 - subnet mask 255.255.255.0
I was a little surprised that the one Annke would not connect to the NVR.
I now realise the the 2 x Hikvision DS-2CD2T42WD-i5 are a little old,
The previous owner says the problem lies with my NVR,
He said - The bullet cameras have been working on Hikvision NVR DS-7716NI-M4 16. New very powerful 16 channel NVR. And I tend on my DS-7608ANI-M2/8p both bullet cameras working perfectly fine.
I am open to all suggestions to try and get these 3 cameras up and running, with the existing, already working 6 camera's, on the Hikvision HiLook NVR
Hopefully its something silly and an easy fix
Thank you in advance for all your comments.
Hikvision HiLook NVR-216MH-C/16P - network video recorder - second hand
Hikvision DS-2CD2T42WD-i5 - poe camera x 2 - second hand
Hikvision DS-2CD2347G2-LU - poe camera x 4 - second hand
Annke AN-i51EM - poe camera - new
Annke AP-i51DS - poe camera - new
Annke AP-i91DM - poe camera - new
12v power supply
Win 11 PC
The 4 x Hikvision DS-2CD2347G2-LU, Annke AN-i51EM and Annke AP-i51DS cameras activated using SADP and Chrome Browser, and are working fine when connected to the Hikvision NVR.
The Annke AP-i91DM camera activated using SADP and Chrome Browser, and can be viewed through the browser, with the Annke Live View, and configurations adjusted as needed. But will not connect, when plugged in, to the Hikvision HiLook NVR.
The 2 x Hikvision DS-2CD2T42WD-i5 cameras are already active, and I am able to adjust their IP range, using the 12345 password, with an on-screen confirmation, 'Parameters modification completed' in SADP, so I am assuming the password is good ! They will open Chrome Browser, but, 'This site can't be reached' 'refused to connect' is displayed across the browser page. These camera's will not connect when plugged into the Hikvision HiLook NVR either. Enable DCHP is greyed out and not available in SADP. The gateway and subnet are in the correct range - 192.168.0.1 - 192.168.0.100 - subnet mask 255.255.255.0
I was a little surprised that the one Annke would not connect to the NVR.
I now realise the the 2 x Hikvision DS-2CD2T42WD-i5 are a little old,
The previous owner says the problem lies with my NVR,
He said - The bullet cameras have been working on Hikvision NVR DS-7716NI-M4 16. New very powerful 16 channel NVR. And I tend on my DS-7608ANI-M2/8p both bullet cameras working perfectly fine.
I am open to all suggestions to try and get these 3 cameras up and running, with the existing, already working 6 camera's, on the Hikvision HiLook NVR
Hopefully its something silly and an easy fix
Thank you in advance for all your comments.
Last edited:
