Search results

One U is 1.75 inches

It's called Vlan, requires managed switches to setup correctly.

In general you should never send VLAN-tagged frames through unmanaged switches, there is no value in doing so. If you do, and the switch faithfully preserves 802.1q, then treat the unmanaged switch as if every port is a trunk port without any VLAN restrictions. Which means all paths out should...

Spec for camera only talk about Wansview Cloud App and Alexa. No mention of Onvif support.

Try plugging the camera directly in the switch that would rule out any cable length problems, or try a different switch.

The problems you will have with the Xeon is there is no intel GPU on the chip, dell used 2 MB maxtor video chip on Xeon systems. You will need to do GPU passthrough, video will still be choppy from my experience. Have a few R720 & R730 in esxi. My esxi I9 11900K blows away and of my dual Xeon...

Is the computer you are using to configure on the same network 192.168.1.x with the camera.

What is the CPU in the server? Most Xeon cpu do not have any GPU built-in and have a cheap 2 mb video chip on the board, have some dell r720 dual xeon with 64 total core and blue iris runs like crap. To get better performance on server I would install Nvidia card and have that do all the BI...

Window 10 has built in memory checker. Search for "Windows Memory Diagnostic" in your start menu, and run the application and reboot.

Did you install the GPU version of deepstack and the Cudnn and cuda 11.3, also remove the cpu version

Had it up and running in less than 5 Min, camera was at factory defaults, Did not have any problems.

Just received the SD52C225U-HNI Perfect Condition, A+ Thanks Andy!

Will take the SD52C225U-HNI PM Sent

They work good, never had any problem with the splitters.

You can use a USB C 5V poe splitter, have used and works good. https://www.amazon.com/UCTRONICS-PoE-Splitter-USB-C-Compliant/dp/B087F4QCTR/ref=sr_1_3?crid=TYK8719551SV&keywords=amcrest+usb+c+poe+splitter&qid=1646798410&sprefix=amcrest+usb+c+poe+splitter%2Caps%2C76&sr=8-3

Yes the cisco can do inter routing, but your Asus router will not know anything about the vlan to pass to the switch from WAN or VPN

If you want Vlan's you need a router that has Vlan capabilities, it does not matter that you have setup L3 on the switch, it still needs to be routed to something and the Asus does not support Vlan tagging, You would be better off using 2 nics setup

I not sure if the Asus 68 supports vlans, do you have the vlan setup in the router? something need to route the vlan to router. How the the switch setup, just tagging?

You using PAL or NTSC? Checked my PTZ1A225U-IRA-N and can do 60fps with NTSC

Is this a new camera installing, try adding existing camera IP for new camera and scan.

Just put on 5.5.5.7 and camera discovery is working

Are you using port forwarding to connect to your BI server from the Wan?

The Noctua will work, but you will get fan error in the log every 10 seconds on the switch, have replaced a few with them, speed sensor does not work with cisco

Here is my Firmware version Software VersionV2.800.0000000.6.R, Build Date: 2020-03-14 WEB VersionV3.2.1.864542 ONVIF Version18.12(V2.4.5.826858)

I'm running 2 of the IP2M-841W-V3

Updated my PTZ1A225U-IRA-N and no issues.

For PTZ tab

These are the settings I use

Avoid at all cost using a port on the UDM, your cpu will run about 50% solid, The UDM will have to forward and route every packet going to BI, not efficient at all.

The CPU is Intel Celeron J4025 2GB memory, running synology + windows on 2 Gb ram. You would need the big Synology for an VM.