Recent content by Samee

i have a hikvision DS-7608NI-I2 / 8P i previously setup push notifications to my iPhone via using app ivms-4500 lite. everything was working well for about 1 year and today it stopped sending me notifications. anybody else's push notifications suddenly stopped? the cameras and NVR have notify...

i have it behind an VPN router. the same time the NAS disconnected from the NVR when it rebooted that the time i lost connection to it. i did check the logs and cannot see anything weird or malicious. just adding the NAS HDD as redundant is an issue. i have downgraded the NAS firmware to rule...

Hi i have a QNAP NAS ts231 and was updating the firmware, it required a restart so i restarted it. it came backup a few minutes later. then noticed i could not connect to the NVR at all. hikvision mode ds7608-ni/e2-8p current fimrware V3.4.96 build170921 i then discovered the unit has been...

if i connect to say a computer at the other end it works fine. now for the POE injector it does not seem to like. the TP link on one end is lit and the Rx light flashes.

i am trying to set the IP address filter on. the cameras ip address is 192.168.0.4 my mac book is 192.168.0.5. i have enabled address filter list and allowed this single ip 192.168.0.5. i have saved the settings, i have a NAS box which it currently using surveillance station and it continually...

have tried that as well does not seem to work, the lights are just not lighting up

@mjb with just the power adapter connected the PWR light is lit with both ends powered up and the modules with the Fibre cables, the Link LED above FX is lit with PWR light. if i disconnect one end the light goes off FX link. so there is connection between the two end points. above TP the...

@mjb yes it is as i have inserted the poe directly into the camera and the other end to a computer to configure it. so the POE injector is working fine. i have a fibre cable and 2 ethernet cables as backup. it works fine of the ethernet cables to the NVR. below is what i am using: TP-LINK...

@mjb i have connected an ethernet cable from my NVR to the SFP media converter, at the other end i connected the other media converter, inserted an ethernet cable on the other end to a POE injector, then connected an IP POE CCTV camera to the other end. i am unable to get anything to view for...

thanks @alastairstevenson i created a static route on my router and it can send me emails with the images. the only other alteration i had to do was create a firewall rule to allow the cameras external access. the image quality is way much better. also what i noticed (a long time ago and still...

ok seems to be some confusion. after enabling virtual host this is what the router logs picked up. i manually allowed a single ip camera say 192.168.10.11 to destination 8.8.8.8 and that removed it from the router logs. i allowed the 8.8.4.4 as well same result. after doing a test for the email...

my nvrs ip address is 192.168.3.2 the cameras have ip addresses from 192.168.10.11 to 192.168.10.15 (only have 5 connected) its gateway is 192.168.10.1 its already pointing to 192.168.10.1 which is the poe gateway. i am missing something?

yes i am aware its google DNS servers, i have changed the address to the Local router gateway address for the DNS server section. so is anyone aware if the cameras are able to send images instead of the NVR? i have played around with some settings but to no avail.

i have checked and cannot see any. at another location i have 2 cameras connected straight into my lan switch and the images are crystal clear

i have a ds-7608 Ni e2/8p nvr and have upgraded the firmware to the latest and noticed there is a virtual host option. i have enabled it and can access the cameras individually. the recorder sends the emails of any movement by default which is not a problem. the only issue is the quality of the...