Search results

i have a hikvision DS-7608NI-I2 / 8P i previously setup push notifications to my iPhone via using app ivms-4500 lite. everything was working well for about 1 year and today it stopped sending me notifications. anybody else's push notifications suddenly stopped? the cameras and NVR have notify...

i have it behind an VPN router. the same time the NAS disconnected from the NVR when it rebooted that the time i lost connection to it. i did check the logs and cannot see anything weird or malicious. just adding the NAS HDD as redundant is an issue. i have downgraded the NAS firmware to rule...

Hi i have a QNAP NAS ts231 and was updating the firmware, it required a restart so i restarted it. it came backup a few minutes later. then noticed i could not connect to the NVR at all. hikvision mode ds7608-ni/e2-8p current fimrware V3.4.96 build170921 i then discovered the unit has been...

if i connect to say a computer at the other end it works fine. now for the POE injector it does not seem to like. the TP link on one end is lit and the Rx light flashes.

i am trying to set the IP address filter on. the cameras ip address is 192.168.0.4 my mac book is 192.168.0.5. i have enabled address filter list and allowed this single ip 192.168.0.5. i have saved the settings, i have a NAS box which it currently using surveillance station and it continually...

have tried that as well does not seem to work, the lights are just not lighting up

@mjb with just the power adapter connected the PWR light is lit with both ends powered up and the modules with the Fibre cables, the Link LED above FX is lit with PWR light. if i disconnect one end the light goes off FX link. so there is connection between the two end points. above TP the...

@mjb yes it is as i have inserted the poe directly into the camera and the other end to a computer to configure it. so the POE injector is working fine. i have a fibre cable and 2 ethernet cables as backup. it works fine of the ethernet cables to the NVR. below is what i am using: TP-LINK...

@mjb i have connected an ethernet cable from my NVR to the SFP media converter, at the other end i connected the other media converter, inserted an ethernet cable on the other end to a POE injector, then connected an IP POE CCTV camera to the other end. i am unable to get anything to view for...

thanks @alastairstevenson i created a static route on my router and it can send me emails with the images. the only other alteration i had to do was create a firewall rule to allow the cameras external access. the image quality is way much better. also what i noticed (a long time ago and still...

ok seems to be some confusion. after enabling virtual host this is what the router logs picked up. i manually allowed a single ip camera say 192.168.10.11 to destination 8.8.8.8 and that removed it from the router logs. i allowed the 8.8.4.4 as well same result. after doing a test for the email...

my nvrs ip address is 192.168.3.2 the cameras have ip addresses from 192.168.10.11 to 192.168.10.15 (only have 5 connected) its gateway is 192.168.10.1 its already pointing to 192.168.10.1 which is the poe gateway. i am missing something?

yes i am aware its google DNS servers, i have changed the address to the Local router gateway address for the DNS server section. so is anyone aware if the cameras are able to send images instead of the NVR? i have played around with some settings but to no avail.

i have checked and cannot see any. at another location i have 2 cameras connected straight into my lan switch and the images are crystal clear

i have a ds-7608 Ni e2/8p nvr and have upgraded the firmware to the latest and noticed there is a virtual host option. i have enabled it and can access the cameras individually. the recorder sends the emails of any movement by default which is not a problem. the only issue is the quality of the...

i am based the UK and was wondering how to ground the NVR? in the UK we have a 3 pin plug where there is a earth pin on the socket which is earth. should this be sufficient or do i need to use the screw ground on the device it self? i just trying to protect my self as i do have external cameras...

ok thanks i have selected the below x1 OM3 Aqua Fibre Optic LC LC Duplex MM 50 125 Patch LSZH Cable 30m - FB3M-LCLC-300 - kenable for HDMI Optical TOS Network Ethernet RJ45 Scart Audio Phono Jack USB Firewire 800 ADSL Cable Leads x2 TP-Link MC220L Gigabit SFP Media Converter, MC220L x2...

@mjb i have seen this x1 Search results for "fiber cables" | Ebuyer.com x2 TP-Link MC200CM Media Converter - Ebuyer what do you think of this combo? i dont suppose it will inject power over the cable to power the camera?

i have a hikvision ds7608ni-e2/8p poe nvr and a ds23032 camera i will be connecting. so no switch only the built in poe switch on the NVR

i will be running them in a separate conduit. i believe that there has to be a set distance between the two power and ethernet, some places i have read 2 inches and other 12 inches. the surge protector i would only require one for a single cable or 2 for both ends? as for fibre i am considering...

im in the process of having a shed built at the back of my house, there will be power put in at some pont. i am deciding to run 2 cat6a cables. i believe ethernet cables and power cables don't mix very well if there sit next to each other. what options have i got? will placing bricks between...

yes its how you have got it. its the same from my end obviously the ip address are different

i have a hikvision Ds-7608ni e2/8p nvr and ds2032 cameras. i am trying to access the web interface of each device on my Apple Mac and it says no plugin. i have installed the plugin from hikvision portal website and it still does not work. any ideas on what i am doing wrong?

i have a camera at the back of a building, and further back its quite dark and the IR illuminator on my hikvision DS-2032 does not reach there, therefore i need recommendations on which illuminator to get the distance is about 30 meters. i am based in the UK so any place in the UK would be...

i have a hikvision ds7608ni-e2/8p and have a firewall VPN router in place. i have by default stopped all traffic going out from the NVR and only permitted DNS 8.8.8.8 and 8.8.4.4 and ip address ranges of the email servers the NVR uses when motion is detected etc. i have been monitoring the...

ezviz was disabled, the only service i forgot to disable was hikision DDNS. i have disabled it earlier and it seems to me ok now. i will leave it for a few hours and get back, but so far so good.

Hi guys i have purchased a VPN firewall/router and my recorder is connected to the VPN router, it send me emails and i can view the cameras fine. i have enabled the firewall logs on the router and the recorders ip address keeps sending something to address 52.31.138.92 and 54.154.135.147 i...

I do have a small hdd in the NVR it's about 160gb which today I had to upgrade to 1tb, as I needed to put the hdd elsewhere to be used. The NAS has not given me any problems, i had it for 4 months now and the only time I have to restart it is when I do an upgrade of the firmware. as I have...

My reason for doing this is because where the camera system is being used nobody lives there and goes there that often, so if somebody decides to rob the place they can take the NVR but the footage will not be in recorder. so at least I would have footage for the event. Also it's hidden in a...

Hikvision ds7608ni-e2/p with a Nas attached Qnap ts-131 with a 4tb Wd purple drive. Drive is now completely full and in the night it seems the NVR rebooted 6 times and with chunks of black blocks where it did not record when it was set to continuous record. overwrite is enabled on the NVR, is...