Recent content by pyspilf

  1. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    Just installed and tested .5.9.9.42 with some of the cameras that had the issue, and now everything works fine after a reboot. ONVIF reconnects and no warnings.
  2. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    Latest info, after checking with Blue Iris support, email from Ken If this works as expected, it will help a lot in ensuring cameras relying on ONVIF for triggering are always properly active
  3. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    Quick update - while I wait for BI Support to let me know if they have any solution for this, I have found a workaround and I tested it successfully. This assumes use of MQTT and some system to issue an HTTP request. In my case: 1. Blue Iris sends a MQTT message on Signal Loss and Signal...
  4. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    After a lot more looking into it, and reading on a few other sites/forums, I had a look at time stamps: Here is when the camera is working fine (or if it has been reset in BI after a reboot fails to work properly with ONVIF, and then works fine): And here is after a reboot when ONVIF is not...
  5. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    And last update so far - I have tested on 5.9.9.19 and 5.9.9.36 and the issue is still there, both on a 5442 and a 2431 camera, regardless of if ONVIF authentication is on or off... in summary, reboot is working fine, but ONVIF is not after the reboot and only recovers after asking BI to...
  6. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    Update: So I have made a few adjustments, I think the loop may have been caused by the 30 seconds being too low and the reboot after 3 attempts, since these cameras take a while to reboot. Having changed it to this, as shown below (45 seconds and 5 attempts) it no longer loops and reboots OK...
  7. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    Hi Tony, For both signal loss and restore, the only thing I configured is for BI to send a MQTT message with a simple JSON payload, that I consume in my HomeSeer system and then send to InfluxDB, as I am building a Grafana dashboard with a state timeline for each camera. The purpose is to...
  8. pyspilf

    Strange issue recently - Dahua cameras rebooted via BI are in a loop...

    On occasion, the odd camera will go into No Signal, and I have always first tried to reset the camera or reboot it via BI. If that doesn't work, then I go to the camera GUI or power cycle it, etc. I have recently observed something new, and a bit odd... it seems to be happening for Dahua...
  9. pyspilf

    Trying to fix intermittent fault - question about nvidia drivers...

    As promised, update. Installed the PA120SE V3 (was fun to learn the LGA1150 socket requires a plate underneath the motherboard, so it was a complete teardown...) - and things are very tight even in a 4U case, but with all installed and cables inside as neat as possible to not interfere with...
  10. pyspilf

    Trying to fix intermittent fault - question about nvidia drivers...

    I concur! I am very careful with things like this. When replacing the processor I cleaned both the heatsink and the CPU with isopropyl alcohol and made sure to get no oil/fingerprints/dust etc on any surface and applied what I considered to be a decent enough amount of thermal paste... but...
  11. pyspilf

    Trying to fix intermittent fault - question about nvidia drivers...

    Thanks! Yes, precisely that is the one I was looking at for a new build I hope in the next few months with a 14th gen CPU, and it was widely recommended for a 4U case OK, I had no idea the temps were that high... I will turn it off before I cook this one too, and go get a better cooler...
  12. pyspilf

    Trying to fix intermittent fault - question about nvidia drivers...

    Oh, well, to be honest, I hadn't thought of that as the CPU fan is always running relatively slow, so I assumed it wasn't heating enough to require more cooling... CPU is usually running in the low 20% or less, only spikes a bit when raining or windy obviously... and I have never overclocked it...
  13. pyspilf

    Trying to fix intermittent fault - question about nvidia drivers...

    Just in case anyone comes across a similar problem, the final solution for me was to source a second hand replacement i7-4790K CPU and now all works fine (or so it seems for the moment). Baffles me as to why a failing CPU would produce kernel errors clearly identified as being caused by the...
  14. pyspilf

    Trying to fix intermittent fault - question about nvidia drivers...

    So, clearly going forward with the Nvidia drivers was not a good idea... had Windows check for updates, and it updated Nvidia to 560.94... resulting in LiveKernelEvent 193 instead of 141 ... just about 1-2' after starting BlueIris. As long as BlueIris is not running (i.e. CP AI is sitting idle)...
  15. pyspilf

    Trying to fix intermittent fault - question about nvidia drivers...

    I am experiencing a frequent issue where the BI server completely freezes. I have narrowed it down to a problem with the video card. This is windows 10 system and these issues (LiveKernelEvent 141) started happening after Windows decided to update some components despite my configuration to not...
    • pyspilf
    • Thread
    • Replies: 9
    • Forum: AI
See more
Top Bottom