Recent content by perfect777

  1. P

    Area of Interest (AoI) Greyed Out

    Thanks for the advice. Edit: it appears that this is a result of "dual streaming". I was able to disable the sub stream (which enabled the AoI)... but the AoI is removed/greyed out the moment that I re-enable the sub-stream...
  2. P

    Area of Interest (AoI) Greyed Out

    Hello! I'm trying to edit the Area of Interest on one of my cameras. I'm trying to avoid facing a partial wall and a neighbor's window. I've used AoI on other cameras, but the option seems to be greyed out (even for an existing camera where AoI is set and working - I can no longer edit...
  3. P

    Help with Drive Overallocation

    I already changed it (per your recommendation) - but it was wayyy more than 100MB!! I think it was a few hundred GB!
  4. P

    Help with Drive Overallocation

    Good call! I just went and changed this. Never considered how this works before...
  5. P

    Having issues with Amcrest IP3M-941 Wireless (Blue Iris Main Stream = 0.00 FPS)

    Hey - this (mostly) worked!! I'm not getting an FPS (and the 1080p MP appears to be working!) I did have to remove the "&proto=Onvif" code in the stream profile for it actually connect:
  6. P

    Having issues with Amcrest IP3M-941 Wireless (Blue Iris Main Stream = 0.00 FPS)

    I tried both of those Make/Model profiles and neither fixed the Main FPS issue...
  7. P

    Having issues with Amcrest IP3M-941 Wireless (Blue Iris Main Stream = 0.00 FPS)

    I don't recall ever rotating or changing the camera in the GUI (how can I tell?) I bumped up the buffer to 40MB. I'm not 100% sure what you meant by the "blank box". I was able to change the resolution to 1080p in the Amcrest settings, but the main FPS is still 0.
  8. P

    Having issues with Amcrest IP3M-941 Wireless (Blue Iris Main Stream = 0.00 FPS)

    wittaj - thanks for the super fast response (as always)! I made the changes that you suggested - but the camera signal doesn't appear to be found by BI (I confirmed that my user/password are correct). If I remove the "&proto=Onvif" from the end of the stream profile, the camera is found -...
  9. P

    Having issues with Amcrest IP3M-941 Wireless (Blue Iris Main Stream = 0.00 FPS)

    Hi All! I have a single Amcrest IP3M-941 wireless PTZ camera that I use in a location where running ethernet was not practical. I have 23 other Amcrest/Dahua cameras using POE. All of this is running in Blue Iris 5.7.8.1. My issue that the substream shows up fine, but the main stream usually...
  10. P

    One of my cameras will not open at full res in UI3 (but works fine directly in BI)

    It doesn't appear that I have this enabled: My UI3 (and BI) profile is "Active" - not sure how to correlate that to the "Streaming 0/1/2" encode profiles.
  11. P

    One of my cameras will not open at full res in UI3 (but works fine directly in BI)

    Yes - when I double click the camera (to make it full screen), it displays in full resolution. Note - it doesn't say "Main Stream" anywhere - but I'm certain that it is.
  12. P

    One of my cameras will not open at full res in UI3 (but works fine directly in BI)

    I think so - but how can I tell? It's one of 24 cameras - the resolution is like 360 x 360 when viewing "All Cameras" in the BI Console (not UI3).
  13. P

    One of my cameras will not open at full res in UI3 (but works fine directly in BI)

    I have 24 cameras running in BI 5.7.8.1. 1 (and only 1!) of these cameras does not like to play nice in UI3. However, it works just fine directly in BI. This camera is a Reolink RLC-410 (1 of 10 cameras in my system). I have it set for mainstream (12FPS) and substream. The substream works...
  14. P

    Help with Drive Overallocation

    Thanks for this advice - but they were already disabled (I deleted any restore points on that drive just in case...)
  15. P

    Help with Drive Overallocation

    Thanks - I decided to delete all of the recordings from this drive and try again. I am aware that the usable space in a 3TB drive is 2.72TB (I mention that very point in my original post). I set the limit size to 2600 and this cleared the over-allocation. I still don't understand why it...
See more
Top Bottom