Recent content by Covy

  1. Covy

    IPC-Color4K-X no connection after IP change

    I can admit it... It was my mistake. I had forgotten that those are the only 2 cameras I ran all the way back to the switch before my basement walls were completed. The rest are run through a POE switch in the garage. I got up top there and saw all the blinky-blinky saying network was working...
  2. Covy

    IPC-Color4K-X no connection after IP change

    Good points, I will do some more checking. There have been no power changes, but I can certainly climb up to the POE switch and pull, wait 20, and re-plug.
  3. Covy

    IPC-Color4K-X no connection after IP change

    AngryIP shows them all except those couple as well: So - I'll have to get a ladder and pull them down tomorrow to reset. EDIT: post game in above... I tried 2 different PC's (one real, one VM). Different browsers and also direct from Blue Iris. Nothing shows them, unfortunately on...
  4. Covy

    IPC-Color4K-X no connection after IP change

    I verified each camera multiple times before hitting save. These are the only two that did not come back. My IP Addresses are like this: Front Camera 192.168.112.10 Reolink Garage Camera Inside 111.106 192.168.112.11 Reolink Garage Camera Front 111.26 192.168.112.12 Amcrest Yard...
  5. Covy

    IPC-Color4K-X no connection after IP change

    I put all of my cameras on a VLAN. I have 8 total cameras right now with a smattering of Reolink, Amcrest, and then 2 of the EmpireTech IPC-Color4K-X cameras. All of the cameras took the IP properly, but only the 2 EmpireTech cameras no longer respond after updating the IP address. The change...
    • Covy
    • Thread
    • Replies: 10
    • Forum: Dahua
  6. Covy

    Blue Iris, Alerts, Stopped running python script

    I put a python script in place recently to send alerts to Pushover. It worked fine initially with this configuration: The script itself is on Github at: GitHub - scudre/pushover-blueiris: Python script to send Blue Iris motion detection alerts via Pushover I added some code to the script...
  7. Covy

    Blue Iris seems to be recording oddly

    Gotcha. Also - I think my real problem was that I assumed the clips would show me where things happened. I had the settings for Alerts set up to 10GB and that was only saving a few days worth of alerts and then deleting them. At least that is what I think I was doing. I had it set up like...
  8. Covy

    Blue Iris seems to be recording oddly

    I was looking through my camera feeds (haven't in awhile) and noticed that going way back it shows my cameras at 12:00:00AM, 8:00:00AM, and 4:00:00PM on every camera all the time like this: This set here shows a person detected on the 4:00:00pm recording. The problem is, that didn't happen...
  9. Covy

    IPC-Color4K-X stopped working

    Just as a followup... took me some time as I was a bit busy with other things (pesky work stuff), but I pulled the RJ45 and wired a new one on (male instead of female), plugged into my network, and the camera is working! Yes, now I will have to install myself with some protection. Thank you...
  10. Covy

    IPC-Color4K-X stopped working

    Thanks, will give the Deoxit a try. No, it was not protected properly - Silicon sealant was used similar to marine applications from what my buddy said.
  11. Covy

    IPC-Color4K-X stopped working

    I have 2 of these cameras since May of last year as i recall. One of them always worked. The other one seems to stop working now and again. But - without me doing anything it suddenly will work. it is up higher on the house, but since it is nice outside I figured I would go have a look...
    • Covy
    • Thread
    • Replies: 11
    • Forum: Dahua
  12. Covy

    Camera setup - settings help

    awesome, thank you. I have made some of those settings adjustments on the EmpireTech cameras and will do some testing today (and tonight at dark). I'll get my other cameras adjusted also.
  13. Covy

    Camera setup - settings help

    I've read a bit on the forums here, but still confused a bit on how to tweak the settings of each camera to optimal. I have not really done any settings adjustments for the most part (analysis paralysis, probably). Here is an example of my EmpireTech Cameras: I have ready that 30FPS is...
  14. Covy

    Cameras recording too late

    Wasn't aware of that, but too late now. I have 2 EmpireTech cameras for important zones and an Amcrest for a garage zones. So far the Reolinks have worked well except for this - but that doesn't appear to be related to the brand.
  15. Covy

    Cameras recording too late

    Are these checkboxes the ones I should uncheck? I changed Interframe to 1x on both cameras. I will have to check my other EmpireTech and Amcrest cameras also.
See more
Top Bottom