I need a Ethernet/power cable pigtail for an EmpireTech 4MP Ultra Low Light Turret IP Camera. Is there anywhere to buy one? I'm not having any luck.
I need a Ethernet/power cable pigtail...
- Thread starter okestone
- Start date
It should come with a pigtail for both Ethernet and separate power. But is there a reason you aren't just connecting it with PoE (Power over Ethernet) so you don't need a separate power connection at the camera?
If you don't already have a PoE switch, but just want to power this one camera, you can buy a single PoE injector.
I'm sorry, I should have been more clear about what's going on.
This camera was installed and working for a couple of years until moisture got in the RJ45 part of the pigtail connector and corroded it. I have tried everything to clean it up and resurrect it, but to no avail. So I need to replace it if possible.
This camera was installed and working for a couple of years until moisture got in the RJ45 part of the pigtail connector and corroded it. I have tried everything to clean it up and resurrect it, but to no avail. So I need to replace it if possible.
If you can figure the color to what pin, you can crimp on a RJ45 on to the wires.
Hint; there are diffrent crimps for stranded and solid wire.
Hint; there are diffrent crimps for stranded and solid wire.
+1^^^.
Since your'e lucky enough to still have the pigtail intact (too many come here and ask AFTER they've cut it off or someone else ripped it off and have no idea of the pinout/color code) write down the color code as it appears on the blank image below, being careful to match color to pin number then you can punch it down to a female Keystone jack or crimp onto a male RJ-45 (NOTE pin layout!) and use a waterproof coupler (bulky).
Do you have a DVM or continuity checker? If so, could you strip a tiny amount of insulation off each wire and see which color goes to which pin of the RJ-45 female?
Since your'e lucky enough to still have the pigtail intact (too many come here and ask AFTER they've cut it off or someone else ripped it off and have no idea of the pinout/color code) write down the color code as it appears on the blank image below, being careful to match color to pin number then you can punch it down to a female Keystone jack or crimp onto a male RJ-45 (NOTE pin layout!) and use a waterproof coupler (bulky).
Do you have a DVM or continuity checker? If so, could you strip a tiny amount of insulation off each wire and see which color goes to which pin of the RJ-45 female?
RESOLVED: Well it didn't seem like a replacement cable was going to be an option so I set out to repair it. Since I am using the camera with POE, I cut the cable just above the external power jack which left me with 6 wires with standard rj45 colors except without blue striped and brown striped wires, but an added red and black wire. Used Google to determine blue with stripe is +, and brown with stripe is -. Connected it and it functions as designed.
Sure! Standard RJ45 pin-out, except red goes to pin#5 (blue stripe) and black to pin #7 (brown stripe).
As a fly on the wall, I'm thinking it was a mistake to hook the red and black wires to the rj45. The red and black wires are for the 12 volt power input. If you connect to a POE switch (usually running POE mode A) it might be moot. But if you use a POE injector (usually mode B) you'll be sending nominal 48 volts into the camera's 12 volt input. It's possible that with the intact pigtail, the brown wire goes to both pins 7 and 8 of the RJ45, and the blue wire to pins 4 and 5.
Here's a picture somebody else made for an older camera. No guarantee that the red/black situation is the same for yours, but I'd be willing to bet a nickle that it is.
Flintstone61
Known around here
Like the diagram above ,,,,from what Ive seen over the years here is that many cameras use a nonstandard wiring color code. there are pictures here( edit-like the one above) on the forum
I think only 6 wires are crimped into the RJ-45 on Dahua OEM's from 1-2 years ago....no idea what a new cam wiring looks like.
I think only 6 wires are crimped into the RJ-45 on Dahua OEM's from 1-2 years ago....no idea what a new cam wiring looks like.
That's correct. ...thus leaving 2 pins for the red and black power supply. Any way, it works great.
You might as well be talking to yourself, IMO....my suggestion for using a DVM or continuity checker to confirm wire color to pin assignment was apparently ignored as well, so.....
Maybe the POE is 802.3af/at compliant and won't "talk" to the red/black so no power from the PSE to them.
Last edited:
Flintstone61
Known around here
Well, I guess we all learned something that you can make a mistake and thing still works.....
Take the win for a working camera, put please don't recommend this red black crimp as a Global solution to the masses.
@TonyR im sure the power/data negotiation from the switch musta decided to not power that pair .
Take the win for a working camera, put please don't recommend this red black crimp as a Global solution to the masses.
@TonyR im sure the power/data negotiation from the switch musta decided to not power that pair .
Most switches are mode A and never power the brown and blue pairs.
gstoa
n3wb
I too had the same issue of moisture corroding the RJ45 connector in my EmpireTech 4MP POE camera's dongle. After cutting off the dongle (including the 12v power, since it's not used) I replaced with an RJ45 with pass through specific for stranded wires. Using an RJ45 with Pass Through made things much easier as I could easily pull individual wires through the right pin in the right order. The pinout for my camera's RJ45 is as follows (which matched the image tigerwillow1 provided):
Position: Color
1: white/orange
2: orange
3: white/green
4: blue
5: unused
6: green
7: unused
8: brown
Position: Color
1: white/orange
2: orange
3: white/green
4: blue
5: unused
6: green
7: unused
8: brown