EZVIZ DB1 Unable to finish set up after firmware update

N

NotEZ_viz

n3wb
Oct 24, 2020
3
1
New Jersey
Hi,
I installed a DB1 doorbell earlier this year, have it set up to record to my Synology (and SDcard) and everything worked as it should. I recently updated the firmware and now I cannot use my doorbell. Here's what's going on:

I can reset the doorbell and set up the Wifi, the doorbell connects to Wifi (I hear the announcement). But the EZVIZ app fails to complete setup, it stops at 90% progress, with an error screen that says "Configuring Network Failed" at the top and an error message "Sorry, connecting to network failed".

But, I can access the doorbell via the Batch Configuration software and I can see the video stream.

I tried going back to an older firmware before I realized I couldn't and then updated to the latest I found on this website : V5.2.4build 2002220. No change. I tried setting up via the iOS app and the Android - same result. I'm almost certain now it has something to do with my network/router but for the life of me I can't figure it out. If anyone has seen this before and can suggest a fix I would really appreciate it!

Thanks
 
normel said:
Another example of : dont touch a working thing :)
Click to expand...

Yeah - I had set it to not refresh and then was tempted to do it. Learned my lesson! Does anyone have any suggestions? I'm almost certain it's something to do with my network config since I can view the RTSP stream just fine, use the batch configuration tool to look at settings remotely, just can't get the thing to finish installing via the app and working like a doorbell.
 
Welcome to the forum!
You can try posting your question in the linked thread below. Extensive discussion about variants of the same doorbell.
Good luck!

New RCA HSDB2A 3MP Doorbell IP Camera

...I would do it so that the tasmota device sets an MQTT... I am actually publishing to MQTT, using node-red to pick it up to push to Pushover notification. I'm already doing a few other things in node-red, but most of my functionality for this mod is done via Tasmota rules.
ipcamtalk.com ipcamtalk.com
 
windguy said:
Welcome to the forum!
You can try posting your question in the linked thread below. Extensive discussion about variants of the same doorbell.
Good luck!

New RCA HSDB2A 3MP Doorbell IP Camera

...I would do it so that the tasmota device sets an MQTT... I am actually publishing to MQTT, using node-red to pick it up to push to Pushover notification. I'm already doing a few other things in node-red, but most of my functionality for this mod is done via Tasmota rules.
ipcamtalk.com ipcamtalk.com
Click to expand...

Thanks! (and you other responders on this thread). I wasn't able to get my DB1 working again and gave up for some time. Until today, when I found an older firmware version posted on ipcamtalk (sorry, I can't find that thread now). I used the batch configuration tool to upload this version (reported by my DB1 as build 191211) and voila! everything works again - including ringing the internal mechanical doorbell!

So, the lesson learned is -do not upgrade no matter how tempting it might seem unless you're willing to risk a lot of unnecessary hackery.
 

Attachments

  • Like
Reactions: dg449680
NotEZ_viz said:
Thanks! (and you other responders on this thread). I wasn't able to get my DB1 working again and gave up for some time. Until today, when I found an older firmware version posted on ipcamtalk (sorry, I can't find that thread now). I used the batch configuration tool to upload this version (reported by my DB1 as build 191211) and voila! everything works again - including ringing the internal mechanical doorbell!

So, the lesson learned is -do not upgrade no matter how tempting it might seem unless you're willing to risk a lot of unnecessary hackery.
Click to expand...

Hi, Would be interesting to fine out how you configured the configuration tool. I'm having exactly the same problem but having a few issues with the CT app.
 
NotEZ_viz said:
Thanks! (and you other responders on this thread). I wasn't able to get my DB1 working again and gave up for some time. Until today, when I found an older firmware version posted on ipcamtalk (sorry, I can't find that thread now). I used the batch configuration tool to upload this version (reported by my DB1 as build 191211) and voila! everything works again - including ringing the internal mechanical doorbell!

So, the lesson learned is -do not upgrade no matter how tempting it might seem unless you're willing to risk a lot of unnecessary hackery.
Click to expand...

Today I have the same problem after a firmware update. Adding in the app stuck at 90%, but connected to my Wifi (i can see the stream)
Flashing it back to 191211 didn't help for me. Can you remember what else you did? Cut off the power, reset,...? Thanks
 
Deurenkletser said:
Today I have the same problem after a firmware update. Adding in the app stuck at 90%, but connected to my Wifi (i can see the stream)
Flashing it back to 191211 didn't help for me. Can you remember what else you did? Cut off the power, reset,...? Thanks
Click to expand...
Same here... First and last time I bought EzViz device. :(
 
same issue on my side, stuck @90% when registering the db1, since update to firmware 211011, already flashed the same firmware, without solution, going to try older firmware now
 
qbic2007 said:
same issue on my side, stuck @90% when registering the db1, since update to firmware 211011, already flashed the same firmware, without solution, going to try older firmware now
Click to expand...

I already gave up and installed the old ringer. No firmware worked. The previous one did, but lost connection after a few hours and always went back to ap mode automatically. Very frustrating. Never update a working thing!
 
Deurenkletser said:
I already gave up and installed the old ringer. No firmware worked. The previous one did, but lost connection after a few hours and always went back to ap mode automatically. Very frustrating. Never update a working thing!
Click to expand...
that would be nice but the thing auto updates from the app ....
 
You must log in or register to reply here.
Top Bottom