Search results

Hi back from nz

The will be a magic dns name of each node the name should be accessible I assume windows is the blue iris? Also in the tailscale iOS app if you click on the windows machine name you can get ip. That should be accessible from your phone if tailscale is running on both (active on iOS and...

If you’re mucking about with cloudflare, you might as well use an Argo tunnel. but then, and whoamis complicated method, both least blueiris fronting the internet authentication. a vpn or tailscale doesn’t.

Having done vpns in the past, both pptp and later IPsec. Becuase my unifi gear supported it. I’ve now disabled in favour of tailscale. So much easier. install on phone. Install on device in network (blue iris machine (windows?) Will do. And off you go. You can fiddle with dns and subnet...

I use it for home assistant because I’m confident it’s authentication system with password and Totp is robust enough to be exposed. I would like to figure out how to get it behind cloudflare access as well but that would need a service token added to the home assistant app, that is passed through

I'd start by removing a bunch of stuff, and just getting a simple message working. Then add the device, sound, attachments, html message etc. It could be as escaping issue on the html in the message, or the paths for the sound/attachment. I've only every done it in linux. Take it right...

Could you have provided any less information? What is the curl command they are running (minus any tokens/keys) What does the response look like (actual, not an interpretation of it).

Not for cameras, but I do use it. For web access you could use it behind their access controls But if you wanted access via mobile, then it's a bit like port forwarding. Just opens it up to the outside world and then use the native security controls on the interface for log in. I expect you...

You can self host the unifi controller as well. Even a pi can. Though think your site might be a bit big for a pi.

8888 I think.

I have mine set the following, maybe alarm does it? This is the IVS settings. I do have one camera, that even though this is set, it never posts notification, and I have to revert to motion detection.

I think once the camera is recording an ivs rule, that just setting the phone notification handles it. I don’t think you have to turn on alarm or emails snapshot or anything on the camera

Fingers crossed.

I use pushover via a number of platforms. Not BI though. And I’ve not noticed any delays.

Where are you located, maybe it's regional. I'm oceania/Australiasia

Local

yeah if I could work out the structure of their messages so that you get the link directly to playback, I'd have replaced it years ago - if only to replace channel 1 with the name of the camera.

Maybe send feedback in the app as well. Hopefully they see that.

Cheers thanks. I tried recreating the alerts on the app, so hopefully I haven't upset anything. But I can see them heading out my firewall.

I can see on my firewall that it's getting traffic to port 8888 which was what was required for apples push notifications. But haven't been getting any mesages to the phone since the past 2 days

Dont believe you can. Why the software insists on doing I have no idea. If you cna name things then I'm sure 99% of people would rather seen the name. But i guess logical for us is no logical for the developer

When Audi release their RS6/A6 etron. Can't stand these fake as "truck" like things.

$3.00NZD a litre (for 91 RON) here....not this US gallon stuff that most of you seem to enjoy. in the 90s it was $0.90 NZD a litre.

The recommended way it to get a vpn at home that you can connect to when out. The your phone, when out, is operating inside your home network. You can port forward and allow access in from the internet but that is not recommended as it a security hole. A vpn, while that is also a point of...

As above, if an alarm has an IP module see if there some way, or some project that can control it remotely. Ie for Paradox Alarms, the ParadoxAlamarInterface project exposes PIR and Arm/Disarm state to MQTT so that openhab/home assistant and anything else mqtt can talk to it. The other major...

I’ve got 5 cameras attached to my nvr. And IDMSS app for notifications.. I ha e one camera though, set up in the app, but it won’t post alerts. It trigger events as you can seen them when you search playback. But nothing comes to the app for notifications . I’ve tried deleting all alerts...

Best practice to factory reset then upgrade right?

Would this be the current latest: H_NVR5XXX-4KS2_MultiLang_V4.001.0000003.2.R.201010.bin 10-Oct-2020 05:02 51132k Has anyone tried it?

Cheers, I'll have a dig around.

Anyone ever dug into how this stuff works? I have a camera events docker container than just pulls a snapshot, but I've love to be able to replicate the dmss notifications that link directly to a recording. I've tried capturing packets with wireshark, but don't seem to see anything from the...