Recent content by xplorer

  1. X

    How to install when there is no attic?

    No, corner post/J channel is all one piece
  2. X

    IR halo ring issue in a IPC-B52IR-Z12E S2.

    It is exposed to the weather, no gasket or seal for the plastic trim piece. locks into place with a couple tabs at top and bottom, at the outer most edge. I never paid much attention to it just cleaned it with Windex now and then, I had incorrectly assumed it was smoked/black glass and held in...
  3. X

    IR halo ring issue in a IPC-B52IR-Z12E S2.

    Cleaning behind the plastic cured the problem, Had thin film on the back of the plastic, like it had been wet/dried wet/dried over and over each time leaving a little behind, some tree junk in the mix and dust. Hard to see it until cleaning it, couldn't see it at all from the outside with...
  4. X

    IR halo ring issue in a IPC-B52IR-Z12E S2.

    I took it down and looked at it after seeing the image Revo2Maxx posted, I didn't know the plastic cover over the IR lights could be so easily removed. I found that flimsy piece of plastic had dirt in behind it. Haven't tested it yet as the weather changed cold and hard to tell in the house...
  5. X

    IR halo ring issue in a IPC-B52IR-Z12E S2.

    No not a thing, I cleaned it to be sure.
  6. X

    IR halo ring issue in a IPC-B52IR-Z12E S2.

    Ok I will take the camera down, test it away from anything that could remotely cause IR bounce and post back the result.
  7. X

    IR halo ring issue in a IPC-B52IR-Z12E S2.

    Camera sold as IPC-B52IR-Z12E S2, Under device info it Identifies as IPC-HFW5241E-Z12E-S2 System Version V3.100.0000000.5.R, Build Date: 2023-05-09 Camera suffers from a full circle halo from its own IR illuminators. Sample picture, Please note that here I added the red circle approximating...
  8. X

    HFW5241E-Z12E-S2 install in Blue IRIS

    Ok great thank you very much, that seems to have corrected the problem. No more Events: subscription 8000ffff and zoom function has returned. I have it setup to get plates leaving the driveway, a work in progress.... I would like to add that I did use the search function first before posting...
  9. X

    HFW5241E-Z12E-S2 install in Blue IRIS

    Not sure where to ask this question so starting here, Can I get a little help installing a IPC-HFW5241E-Z12E-S2 ? I bought it from Andy and it is running the firmware it came with, System Version: 3.100.0000000.5.R Build Date:2023-05-09 I'm running BI version 5.7.9.12 I get non stop Events...
  10. X

    100% DeepStack timeouts after BI update (including reverting to earlier versions)

    Yup did all the same steps, stop start BI stop start windows, stop start DS, separately and all three in order etc. Revert to previous working version then back to latest again, pick one in between there try that. When I do update, I do not go beyond the critical/highly stable release. Results...
  11. X

    100% DeepStack timeouts after BI update (including reverting to earlier versions)

    Suffered the same thing "AI timeout" after updating. I tried what you did = I deleted all the redis temporary dump.rdb files, and so far seems to have corrected the problem. I did not reinstall DeepStack, I only removed the dump.rdd file and then restarted BI. (I saved the file so I could...
  12. X

    admin default password - IPC Model: IP420/50

    Try username admin password leave blank User manual? https://www.amazon.co.uk/clouddrive/share/O4sFwTOT16jZrtZQUGUKng5Pxnlmuz4oxotCnMnESdn/w7bo2lNNRfedjAIBzZ5Egw
  13. X

    HFW2231T-ZS Base does not turn

    Yeah no rust and corrosion just what are likely rare events made it non adjustable getting missed by QC. I put shields over cameras so they do not get hit by rain, snow nor to a great degree even direct sunshine. Machining debris plus mill scale not cleared away before assembly, paint got into...
  14. X

    HFW2231T-ZS Base does not turn

    Knowing that it should turn no longer any question about that, I got after it. Took quite a bit of forced but once it moved I was able to separate it and clean it up. Was heavy with machining/mill scale then painted and dried locking it in place, adjustable now like I believed it had to be.
  15. X

    HFW2231T-ZS Base does not turn

    Ok I'll try putting more effort into it but it has never rotated from when new and directly out of the box. Thread where I asked about it after first putting it up. https://ipcamtalk.com/threads/bullet-camera-question.59776/#post-609508 No nut behind it. It was fine the way it was, intended...
See more
Top Bottom