Recent content by J273

  1. J273

    New Reolink Wired POE Doorbell Cam ?

    Yeah ONVIF is switched on and i can view the doorbell through the NVR just can't seem to capture basic motion events through the NVR.
  2. J273

    New Reolink Wired POE Doorbell Cam ?

    Has anyone managed to get their Doorbell connected to a hikvision NVR and get basic motion detection working? I have had mine connected to my NVR since it first came out but never managed to get it to capture even basic non smart events. I can view the camera through hiK-connect which works...
  3. J273

    RJ45 Couplers with POE?

    Ah thanks, didn't know they existed. they're just what i need
  4. J273

    RJ45 Couplers with POE?

    Hi all, I have a few camera's which id like to change their location but i can't run a new CAT6 feed. Is it safe for me to use RJ45 couplers with POE cameras to extend the cat6 feed i already have in place. Something like these? Are they ok to be used with POE? Anyone use them without any...
  5. J273

    1005KI Joystick firmware upgrade.

    Yeah I have the firmware,it's just the app I need to update it. Thanks
  6. J273

    1005KI Joystick firmware upgrade.

    Ive just bought a hikvision 1005KI usb joystick and would like to upgrade the firmware. Reading the manual it says to use buttonboardemo softare. I cant seem to find this software or if it exists? Does anyone know how to upgrade the firmware on these PTZ joysticks? Thanks
  7. J273

    PTZ dwell time change?

    Thanks Yeah i have checked this but id of thought this would be a setting on the NVR itself rather than the camera?
  8. J273

    PTZ dwell time change?

    Hi all, Is there a setting on the NVR (I-series) which will allow you to change the dwell time for a preset?. Ive looked but can't seem to find anything. I have a PTZ camera and currently have it set so that when one of my other cameras detects line crossing the PTZ flick to the preset i have...
  9. J273

    Annke Firmware to Hikvision Firmware: HOW TO

    Ive just bought a few c500's as they were going cheap on prime day. Can these be added to a hikvision NVR on their stock annke firmware using the hikvison protocol not using ONVIF or do i need to flash them to the hikvision firmware for them to work? I have flashed one but found its lost...
  10. J273

    New Reolink Wired POE Doorbell Cam ?

    I use Hubitat and miss having my doorbell integrated into it with my reolink. I previously had a nest and it worked perfectly, turning on my porch lights when an visitor arrives + announcements on my sonos. It's the one thing missing for me and a shame there's no integration and i don't think...
  11. J273

    New Reolink Wired POE Doorbell Cam ?

    Is the lag only there when viewed through your NVR? I had this problem with mine connected through my hikvision NVR it wasn't anything to do with the doorbell. I had to change the FPS and bitrate on the NVR itself and the lag went away.
  12. J273

    UK CCTV install.......Running Cat6 POE cable through Soil stack box section.

    Ok thankyou. I plan on pulling a plastic conduit down first and then run all the cables in that. The HDMI cable I can run that elsewhere so that's not a problem and could leave that out but ideally having 4 x cat6 in a conduit would make my installation alot easier.
  13. J273

    UK CCTV install.......Running Cat6 POE cable through Soil stack box section.

    Hi all. Im UK based so not sure if its different elsewhere but i have a soil stack pipe which run from my kitchen up and out the roof which is housed in a box section (2ft x 1ft). I have my NVR + POE switch located in the loft and would ideally like to run 4 x cat6 cables and an HDMI lead...
  14. J273

    New Reolink Wired POE Doorbell Cam ?

    Im going to try this later today and I'll update the post to see if i have the same problem. Do you have the doorbell on the same IP range as your main cameras 192.168.254....... ?
  15. J273

    New Reolink Wired POE Doorbell Cam ?

    I might have to try that. I have mine connected to a Poe injector and then into my router not connected directly to the NVR
See more
Top Bottom