Recent content by g4m3r7ag

  1. G

    CodeProject.AI Version 2.0

    I am on 5.7.7.10 now and the issue is fixed. Haven't gotten the update for 5.7.7.11 yet but I would hope it remains fixed in that version.
  2. G

    CodeProject.AI Version 2.0

    I did not know that existed, thank you.
  3. G

    CodeProject.AI Version 2.0

    That does seem to be it, I didn't have the option for 5.7.7.5 though as I was on 5.7.7.7 so I dropped back to 5.7.6.8 and all is working again.
  4. G

    CodeProject.AI Version 2.0

    The last few days all of my alerts have started being cancelled as "occupied". When I review the AI analysis the moving vehicle is identified in the first couple of sample images with a confidence greater then my setting, then after the vehicle leaves the frame the sample images start showing...
  5. G

    Two IPC-HDW2431TM-AS lost video in one week

    Did they fail the same way? Reboot loop?. I just had a fourth camera fail, I was beginning to suspect maybe an issue with the Cisco 3750X powering the cameras, except the fourth camera that failed was at a different site that is using a Juniper EX2200. It's even a different brand of Cat5e...
  6. G

    Two IPC-HDW2431TM-AS lost video in one week

    It's been reset about 5 times. It does have a 12vdc plug, but I don't have any 12v 1a bricks, plenty of 12v 2a but no 1a. I'll have to see if I can find one as you said, that's about the last thing to test, but if that fixes the camera is still not usable for me so it would just be trying to...
  7. G

    Two IPC-HDW2431TM-AS lost video in one week

    Have tested with two different POE switches, with different cable runs at two different sites. The original installation site with a Cisco POE switch, and at my house on my desk with an Ubiquiti POE switch. The Cisco switch at the original installation site is a 48 port 3750X that is currently...
  8. G

    Two IPC-HDW2431TM-AS lost video in one week

    No SD Card in the camera, Chrome/IE/Edge all have the same behavior. This camera was not previously added on my BI server but I input the IP/creds and ran the find/inspect Opening 192.168.1.90 port 80... HTTP Get / request... OK ONVIF GetSystemDateAndTime 2022-02-24T03:44:25.000Z Requesting...
  9. G

    Two IPC-HDW2431TM-AS lost video in one week

    The video preview just stays on this black screen with the spinning circle The log shows this sequence repeating endlessly
  10. G

    Two IPC-HDW2431TM-AS lost video in one week

    I mean no video directly in the WebGUI of the camera, not even attached to BlueIris, so no watch dog restarting the camera either.
  11. G

    Two IPC-HDW2431TM-AS lost video in one week

    Just had a third camera with the same symptoms. Video never loads and the camera reboots every ~80 seconds.
  12. G

    Two IPC-HDW2431TM-AS lost video in one week

    find/inspect appears to run without issue, but still no video in either BI or the cameras WebUI
  13. G

    Two IPC-HDW2431TM-AS lost video in one week

    I have 15 of the Dahua 2431's running in Blue Iris and it's been working great for over a year. This week two of them started showing no signal in the Blue Iris console. I can ping their IP address, and I can access the WebGUI, but the video preview is just a black screen. I've tried rebooting...
  14. G

    Motion Detection with dark vehicles at night

    I'm not too concerned with plates just an alert of a vehicle/person coming through. I plan to add another camera in a different spot that may be better for capturing plates. I can try changing some things one at a time to see if it improves. Reading the description, it does sound like HLC would...
  15. G

    Motion Detection with dark vehicles at night

    So is there a Zone crosses config there or just a single zone in use and trigger on any motion in it? I will try unchecking the object travels tonight and see if that makes a difference. The camera is a Dahua 2231, all of the settings are default right now as I didn't configure anything other...
See more
Top Bottom