Recent content by bheremans

Yes settings in putty are important. See first page of thread..

Still subscribed on the thread :-) I did try mine on a raspberry to know sure. the first one got fried, the second one worked on a raspberry, after that I used it on the NVR connection settings in putty (if you use that) are important but also the connected wires...

I used the included power supply to be sure the poe+ switch was not the problem. Unfortunately it is not easy to remove the cam again because of his location. I also hot it that tye cam can't look straight down. The manual says 90° tilt. But that is not true for me..

Did you ever resolved this problem, I also have this problem. I reboot the camera every night , but after some time PTZ is responding badly. Also the sometimes makes a lot of noise when moving. I already switched from POE+ power to the included power supply, but this didn't change anything.

Here is a picture how I connected my longse : https://photos.google.com/share/AF1QipOEpYWH3ELBGTfQbVen5digcpvSkX-DWWP2uh-T1Tqv1bH7rQCFKM5JGLZEXkFw5w?key=OTZJMVJSMEh1YUZtZzRQWjZfcVg1RXN6cGlseHVB

Hi, I didn't have a good firmware either. I actually got it from the longse / herospeed site. After viewing it with an editor i found out it was cramfs file with a litte header that I striped.. But it was alastairstevenson who provided me the different files. I could find the hashes and file...

Hi, it seems very simular but it isn't exact the same. Problem seems similar, mine also did show the boot splash. I was never able to fix it with an usb update. You will need serial acces to fix it the way I did. This photo shows the longsue nvr I fixed, see the attached serial connection ...

If you find a good replacement.. small .. ptz .. audio .. outdoor, let me know. Dahua black face starlight is al little to big and to expensive for me.

I hava a dahua black face to.. When using it in daylight I have stripes :-( It doens't happen with IR ... So my dahua has his problems to (but i can live with it)

My v2 has the same problem.. died in weather between 5 and 15 degrees celsius. No firmware update done. Tried connecting serial console but didn't get any login prompt.. now serial copper contacts broke off. So it's a piece of junk now. Time to order a new one. Mine was with audio and alarm...

My PTZ v2 mini died after some months.. First it would work for some moments minutes with POE.. then I had to connect it with a separate power supply, worked for 2 days.. now nothing.. when i connect power I see the 2 bottom infrared lights verry short. network lights go on but no traffic, no...

because there is no much info for these longse recorders, I just found out how to get the different rtsp streams from the recorder (by debugging freeip android app) : rtsp://user:password@ipadres:[rtspport]/channelandstream channel 1 = 0 channel 2 = 1 channel 3 = 2 stream 1 = 0 stream 2 = 1...

Webinterface is the same as theire ipcams, you need an ocx and internet explorer... The local interface is nice, semi transprant colorfull menus youtube cms software Manual : http://www.longse.com/UpFile/file/Instructions/CMS%20User%20Manual.pdf I bought it for a friend but wanted to update...

Found the password with google before reading your post. 12345 was the correct password ! system fully operational ! I hope the info in this thread will be helpfull for other people bricking their longse nvr :-) Thx for all the help !

Yep the wizards asks a password and the factory default one in the manual 123456 is not working. Also network default config was gone it tried to set 255.255.255.255 as ip.. But I was already able to log in as root with serial console and set an ip with ifconfig. Webapp or local ui app access...