Recent content by ashammah
-
Hikvision DS-KD8003-IME - New video doorbell
Its used for any door that needs to remain secure if the 8003 is removed from the wall by an intruder. I'm using one on my garage door with a keypad. If someone removes the 8003 & keypad to gain entry it won't open the door by just sticking the +- together -
Hikvision DS-KD8003-IME - New video doorbell
This should explain everything -
Hikvision DS-KD8003-IME - New video doorbell
That sounds like it should work. Just set one gate as "Main" doorstation and the 2nd as "Sub" doorstaion. If you want a secure connection for the striker use a DS-K2M061 Secure Door Control Module -
Hikvision DS-KD8003-IME - New video doorbell
I cant get video at all from the 8003 on any sip app or Cisco phone. All debugging shows video working fine but no video shows. If I use Firmware 2.2.58 Calling the 8003 gives a busy signal and calling from 8003 to freepbx gives a constant static. -
Hikvision DS-KD8003-IME - New video doorbell
Very weird. I haven't been able to get video over the 8003 SIP at all. Video to the indoor screen and NVR works fine. -
Hikvision DS-KD8003-IME - New video doorbell
Do you know what port video streams from on the 8003? -
Hikvision DS-KD8003-IME - New video doorbell
From the 8003 I have just a black screen with audio calling from Linphone to 8003 Codecs are enabled i lowered the resolution down thinking that could be it still no video :brainfart: -
Hikvision DS-KD8003-IME - New video doorbell
How did push video from the 8003 to Linphone? I can get a video stream from the Cisco 8865 to Linphone, works perfect. But 8003 to Linphone no video, audio only. Either direct to the 8003 ext, or by pressing the call button and answering on Linphone through the trunk. it was the 8003 all along... -
Hikvision DS-KD8003-IME - New video doorbell
Is the trunk suppose to stay unvail? its registered and working but always "Unavail" Endpoint: Hikvision_Trunk Unavailable 0 of inf OutAuth: Hikvision_Trunk/10000000005 Aor: Hikvision_Trunk 0 Contact... -
Hikvision DS-KD8003-IME - New video doorbell
I haven't been able to get video at all on the Cisco phones. I had to change the conf a bit to get audio to work while the phones have video enabled. I have audio now while the phones have video enabled on them but video doesnt work. The other non video-phones worked fine all along. -
Hikvision DS-KD8003-IME - New video doorbell
Testing again. Its possible to have the Doorphones on SIP extensions for intercom and paging, and have the Doorphone ring through the trunk for doorbell calls Just setup a sip extension and dont add a number to call let the indoor station handle that end. -
Hikvision DS-KD8003-IME - New video doorbell
So, I think im running half SIP, half Trunk. I have to have the SIP setup in session settings for the Sub Door station to work. And SIP to FreePBX has to be present in device configuration to get PBX calls. Doorphones - Main Station, Hik-sip. Indoor station - PBX, SIP Trunking I still cant get... -
Hikvision DS-KD8003-IME - New video doorbell
Hmmm I'm not sure how that would work. If add sip also wouldn't it ring again after the screens finish ringing. I will test tomorrow its late here i'll be up until 8am if I can get them connected again hahaha -
Hikvision DS-KD8003-IME - New video doorbell
Got it! haha. Door station 1 has to be "0" Door stations after it 1,2,3, Video is enabled on the PBX. I have direct video from Phone - Phone. But no direct video Doorphone to SIP phones. -
Hikvision DS-KD8003-IME - New video doorbell
On the older screens its possible. First selected is the main then addition selected become sub stations. Its not doing it on the 9510. I have one set as "Doorphone" and one set as "Main Door station" both calling. But adding another 3. I'm sure I can figure it out. No video from the doorphone...
