I thought I had it fixed but its still not working. I reset it numerous times and the green light goes off and comes back on. I can't connect to it directly through a web page. Config tool will find it and initialize it but even after that I can't connect to it. It's showing it has the new firmware.
IPC-HDW5231R-ZE Rhea V2.800.0000016.0.R.200430 Latest new firmware
- Thread starter EMPIRETECANDY
- Start date
looney2ns
IPCT Contributor
Nope.
Kitsap
Getting the hang of it
Reset sets all of the settings to the default values for the installed firmware. On some models there are a couple of exceptions for the settings. In particular the IP address.
fstfrd50
Getting the hang of it
I have ( 4 ) older IPC-HDW4231E-AS and looking for firmware :V2.800.0000015.0.R, Build Date: 2020-04-30, any assistance is appreciated. This firmware15 works best for me as my other 2 cams have version 16 and would like to return back to my previous firmware, Thank you.
IAmATeaf
Known around here
I might have it, let me take a look and I’ll report back.
Would like the v15 firmware too....one of my 5231 seems to have had the motion sensor stop working...anyone else experience this?
IAmATeaf
Known around here
Sorry for the delay, forgot all about this but here is what I have, hope it's what you are after.
MD5 hash for the file is 8e41910577878c029530b7b649d41465
MD5 hash for the file is 8e41910577878c029530b7b649d41465
Last edited:
Bitslizer
Pulling my weight
- Joined
- Nov 23, 2017
- Messages
- 467
- Reaction score
- 193
Couple page back there was someone asking about this
Stream Smooth
Click , or drag to set the value of Stream Smooth. The higher the value is, the less smooth the stream, but the higher the image definition; the lower the value is, the more smooth the stream, but the lower the image definition. The value of Stream Smooth is 100 by default
source:
Stream Smooth
Click , or drag to set the value of Stream Smooth. The higher the value is, the less smooth the stream, but the higher the image definition; the lower the value is, the more smooth the stream, but the lower the image definition. The value of Stream Smooth is 100 by default
source:
fstfrd50
Getting the hang of it
Henry_G
n3wb
Hi! I have the IPC-HDW5231R-ZE I bought from Andy in 2018. I've never updated the firmware - using 2.622.0000000.18.R, Build Date: 2017-11-10
I have them blocked from the internet. I'm not using the upload function in the camera admin. Things are working fine so I don't think I'll update, but for reference, where can I download the latest firmware? Tried here: Firmwares
Thanks!
I have them blocked from the internet. I'm not using the upload function in the camera admin. Things are working fine so I don't think I'll update, but for reference, where can I download the latest firmware? Tried here: Firmwares
Thanks!
looney2ns
IPCT Contributor
That is what this thread is for, read back a few pages.
Henry_G
n3wb
Thanks for this. For anyone else a bit confused - I am reading multiple ways to get the firmware:
- "Just send Andy a PM"
-"Yes just update through the camera web GUI and you should be good"
-"Index of /images/Files/Firmware"
-From Andy "Lots of guys asked for this fw, i upload on the 1st page again." - This is now obviously what this thread is about - the most recent version is updated by Andy on Page 1.
IAmATeaf
Known around here
Does the attached file in post #1 not open to give you details on how to download the version stated in the thread title?
EMPIRETECANDY
IPCT Vendor
If you found the firmware not work with your cam, can change back to
IP camera very seldom brick, not like NVR.
| DH_IPC-HX5X3X-Rhea_MultiLang_PN_Stream3_V2.800.0000015.0.R.200430.zip |
Last edited:
saggybeans
Young grasshopper
I am using the Dahua IPC-HDW5231R-ZE with firmware V2.800.0000013.0.R. Do you recommend that I upgrade to V2.800.0000015.0.R? Some people in this forum were saying that the camera continuously contacts a Chinese cloud server, what is this all about?
EMPIRETECANDY
IPCT Vendor
If your camera al working well, then no need to make upgrade. I post the update list on the 1st page.
a Chinese cloud server,I haven't hear too much about this, as i know cams right now all use amazon cloud
a Chinese cloud server,I haven't hear too much about this, as i know cams right now all use amazon cloud
EMPIRETECANDY
IPCT Vendor
DH_IPC-HX5X3X-Rhea_MultiLang_PN_Stream3_V2.800.0000015.0.R.200430.bin
1 file sent via WeTransfer, the simplest way to send your files around the world
we.tl
Use this firmware.
EMPIRETECANDY
IPCT Vendor
Looks like the original fw you used are bit old, has big gap may bring some problems.
IAmATeaf
Known around here
I think I’ve found an issue/bug with this firmware, all my cams randomly, not too sure under what circumstance right now but I run all my cams with substream 1 disabled and substream 2 enabled. What I’ve found is that the cams revert back to enabling substream 1 and disabling substream 2 which causes BI to then report a no stream error.
I’m not too sure right now but I think it’s associated with powering the cam down ie unplugging the network cable or restarting the cam causes this issue.
I’ll do some more testing and report back.
Edit: scanning back through this thread I see that others reported this issue and it does look like it’s associated with power cycling the cam.
I’m not too sure right now but I think it’s associated with powering the cam down ie unplugging the network cable or restarting the cam causes this issue.
I’ll do some more testing and report back.
Edit: scanning back through this thread I see that others reported this issue and it does look like it’s associated with power cycling the cam.