Camera won't up

RT400

n3wb
Joined
Nov 23, 2022
Messages
4
Reaction score
0
Location
Israel
Hi,
I have flir ip camera that wont up.
i connect to rs232 and see this output :

Code:
U-Boot 2010.06-svn2635 (May 28 2015 - 10:21:40)
I2C:   ready
DRAM:  256 MiB
gBootLogPtr:80580008.
NAND:  HW ECC BCH8 Selected
128 MiB
partition file version 2
rootfstype squashfs root /dev/mtdblock7
TEXT_BASE:80a00000
Net:   Ethernet clocking: 0x52
Detected MACID:0:40:7f:79:6e:73
B50612E found

link up on port 0, speed 100, full duplex
Using cpsw device
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending through gateway 192.168.1.1
Download Filename 'upgrade_info_7db780a713a4.txt'.
Download to address: 0x84000000
Downloading:
Retry count exceeded; starting again
Try again use backup_serverip
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Failed to get info.txt
Fail to get info file!
Init error!
link up on port 0, speed 100, full duplex
Using cpsw device
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending through gateway 192.168.1.1
Download Filename 'failed.txt'.
Download to address: 0x81000000
Downloading:
Retry count exceeded; starting again
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   uImage
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4588224 Bytes = 4.4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ...OK
OK
partition file version 2
rootfstype squashfs root /dev/mtdblock7
can't find corresponding entry
fail to resolve
fail to load bootargsParameters.txt
fail to load bootargsParameters.txt file
get bootargs info failed
cmdLine console=ttyO0 rootfstype=squashfs root=/dev/mtdblock7 init=/linuxrc mem=144M vram=4M notifyk.vpssm3_sva=0xBFD00000 cmemk.phys_stazt=0x89000000 cmemk.phys_end=0x8a000000 cmemk.allowOverlap=1
crashflasg:1, logmagic:54410011.

Starting kernel ...
Any idea ???
 

RT400

n3wb
Joined
Nov 23, 2022
Messages
4
Reaction score
0
Location
Israel
i see in other post that board same as what i have, i run this command:
Code:
setenv dh_keyboard 0
saveenv
reset
after this i can see after boot more info...
Code:
U-Boot 2010.06-svn2635 (May 28 2015 - 10:21:40)
I2C:   ready
DRAM:  256 MiB
gBootLogPtr:80580008.
NAND:  HW ECC BCH8 Selected
128 MiB
partition file version 2
rootfstype squashfs root /dev/mtdblock7
TEXT_BASE:80a00000
Net:   Ethernet clocking: 0x52
Detected MACID:0:40:7f:79:6e:73
B50612E found

link up on port 0, speed 100, full duplex
Using cpsw device
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending through gateway 192.168.1.1
Download Filename 'upgrade_info_7db780a713a4.txt'.
Download to address: 0x84000000
Downloading: *
Retry count exceeded; starting again
Try again use backup_serverip
link up on port 0, speed 100, full duplex
*** ERROR: `serverip' not set
Failed to get info.txt
Fail to get info file!
Init error!
link up on port 0, speed 100, full duplex
Using cpsw device
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending through gateway 192.168.1.1
Download Filename 'failed.txt'.
Download to address: 0x81000000
Downloading: *
Retry count exceeded; starting again
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   uImage
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4588224 Bytes = 4.4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ...OK
OK
partition file version 2
rootfstype squashfs root /dev/mtdblock7
can't find corresponding entry
fail to resolve
fail to load bootargsParameters.txt
fail to load bootargsParameters.txt file
get bootargs info failed
cmdLine console=ttyO0 rootfstype=squashfs root=/dev/mtdblock7 init=/linuxrc mem=144M vram=4M notifyk.vpssm3_sva=0xBFD00000 cmemk.phys_start=0x89000000 cmemk.phys_end=0x8a000000 cmemk.allowOverlap=1

Starting kernel ...
init gLogRamRes: start=0x88f7e000;size=0x80000
init gMemRelimitAddr:0x88ffe000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 35296
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 138MB 1MB = 139MB total
Memory: 135668k/135668k available, 11788k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xc9800000 - 0xf8000000   ( 744 MB)
    lowmem  : 0xc0000000 - 0xc9000000   ( 144 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc002a000   ( 136 kB)
      .text : 0xc002a000 - 0xc0428000   (4088 kB)
      .data : 0xc0428000 - 0xc04682c0   ( 257 kB)
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
console [ttyO0] enabled
Detected MACID=0:40:7f:79:6e:73
Freeing init memory: 136K
mdev: applet not found

UBI device number 0, total 32 LEBs (4063232 bytes, 3.9 MiB), available 6 LEBs (761856 bytes, 744.0 KiB), LEB size 126976 bytes (124.0 KiB)
ubimkvol: error!: cannot UBI create volume
          error 17 (File exists)
UBI device number 1, total 32 LEBs (4063232 bytes, 3.9 MiB), available 6 LEBs (761856 bytes, 744.0 KiB), LEB size 126976 bytes (124.0 KiB)
ubimkvol: error!: cannot UBI create volume
          error 17 (File exists)
UBI device number 2, total 32 LEBs (4063232 bytes, 3.9 MiB), available 6 LEBs (761856 bytes, 744.0 KiB), LEB size 126976 bytes (124.0 KiB)
ubimkvol: error!: cannot UBI create volume
          error 17 (File exists)


[OSA-DRV] OSA Build on Sep  3 2014 at 09:31:31.
[OSA-DRV] SVN NUM: 2598.

[OSA-DRV] Monitor    Task   pid=121   tid=121


[LOG-DRV] LOG Build on Nov 26 2014 at 17:14:32.
[LOG-DRV] SVN NUM: 7339.

[LOG-DRV] ramStart:0x88f7e000;ramSize:0x80000;select:1
[OSA-DRV] Char device create OK !
[OSA-DRV] ERROR  (OSA_fileOpen|478): Open failed
[LOG-DRV] WARN  : open config failed, use default
[LOG-DRV] coreId = 0, logLevel = 2
[LOG-DRV] coreId = 1, logLevel = 2
[LOG-DRV] coreId = 2, logLevel = 2
[LOG-DRV] coreId = 3, logLevel = 2
[LOG-DRV] coreId = 4, logLevel = 2
[LOG-DRV] coreId = 5, logLevel = 2
00:00:01|[OSA-DRV] logPoll    Task   pid=123   tid=123
00:00:01|[PRM-Drv] PRM version : 1.0.0
00:00:01|[PRM-Drv] PRM module(SVN:3701) Build on Mar 23 2015 at 09:01:36.
00:00:01|[PRM-Drv] Region num:4
00:00:01|[PRM-Drv] region={.id=0, .addr=0xbe400000, .len=0x1400000, .cacheable=0, cacheline=128}
00:00:01|[PRM-Drv] region={.id=1, .addr=0x8ca00000, .len=0x3200000, .cacheable=1, cacheline=128}
00:00:01|[PRM-Drv] region={.id=2, .addr=0x8fe00000, .len=0x200000, .cacheable=1, cacheline=128}
00:00:01|[PRM-Drv] region={.id=3, .addr=0xb7800000, .len=0x6c00000, .cacheable=0, cacheline=128}
00:00:01|[PRM-Drv] PRM module(SVN:3701) Build on Mar 23 2015 at 09:02:33.
00:00:01|[PRM-Drv] Reserved shared memory(size:1048576) setup done!
00:00:01|[PRM-Drv] Support 128 hardware spinlock!
00:00:01|[PRM-Drv] Sync initialize OK!
00:00:01|[PRM-Drv] PRM driver install successful!
00:00:01|[PRM-Drv] Add tag[65534] successful!
00:00:01|[PRM-Drv] Add tag[65533] successful!
00:00:01|[PRM-Drv] Add tag[65534] successful!
00:00:01|[PRM-Drv] Add tag[65533] successful!
<6>DMA: Module install successful, device major num = 246
<6>DRV: Module install successful
<6>DRV: Module built on Sep 21 2013 18:24:01
00:00:01|[BND-Drv] Binder.ko Build on Sep 30 2014 at 10:55:40.
00:00:01|[BND-Drv] SVN NUM: 2020.

00:00:01|[BND-Drv] NameServer Initial OK !
00:00:01|[BND-Drv] RPC Initial OK !
00:00:01|[BND-Drv] Create binder memory pool(size:2097152) OK!
00:00:01|[BND-Drv] Binder Initial OK !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[BND-Drv] SR driver initial OK !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[BND-Drv] NS driver initial OK !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[BND-Drv] Binder driver initial OK !
00:00:01|[VPF-DRV] VPF Driver Build on Sep 25 2014 at 15:24:01.
00:00:01|[VPF-DRV] SVN NUM: 2712.

00:00:01|[VPF-DRV] VPF Lib Build on Sep 25 2014 at 15:24:04.
00:00:01|[VPF-DRV] SVN NUM: 2712.

00:00:01|[VPF-DRV] VPF_nodeInit OK
00:00:01|[VPF-DRV] VPF_FrmInit OK
00:00:01|[VPF-DRV] VPF_blkMemInit succeed
00:00:01|[VPF-DRV] Vpf driver initial OK !
00:00:01|[OSA-DRV] PRIV_NODE_3_136T Task   pid=137   tid=137
00:00:01|[SPF] SPF Build on May 19 2014 at 13:42:19.
00:00:01|[SPF] SVN NUM: 6192.

00:00:01|[SPF] SIL initial OK !
00:00:01|[SPF] SPF initial ok !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[SPF] SPF Proc Create OK!!!
00:00:01|[SPF] SPF driver initial ok !
00:00:01|[prc]

PRC Driver Build on May 19 2014 at 14:26:22.
00:00:01|[prc] SVN NUM: 2136.

00:00:01|[SPF] Dai 0 register OK !
00:00:01|[prc] SIL_daiRegister SIL_DAI_MCBSP done
00:00:01|[SPF] Dai 1 register OK !
00:00:01|[prc] SIL_daiRegister SIL_DAI_MCASP done
00:00:01|[prc] Success to init module!
00:00:02|[pdc]

PDC Build on Apr  1 2015 at 09:29:29.
00:00:02|[pdc] SVN NUM: 5187.

00:00:02|[pdc] BASE_LINE: 246
00:00:02|[pdc] OSA_kProcCreate OK
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] PDC_PartionInit ok!!
00:00:02|[pdc] HWID : IPC-HFW8306:01:02:02:12:0F:0C:01:06:01:01:04:3E8:03:00:02:04:00:01:00:00:200
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] binderFlag: 0x1b, funcap: 0x18538b,0x30600,0x3f,0x0
00:00:02|[pdc] videoOut Channel is 0
00:00:02|[pdc] Find Product: IPC-HFW8306.
00:00:02|[pdc] PDC_cfgInit_IPC_HFW8306 >> alarmIn
00:00:02|[pdc] Config size 2604 !
00:00:02|[pdc] SenCfg Match OK,pCfgParams->pCfg: bf188884
00:00:02|[pdc] SenCfgSize: 212 Bytes
00:00:02|[pdc] Init spiBus1  Successed!
00:00:02|[prc] omap_i2c_probe ..., 0
00:00:02|[prc] omap_i2c_probe ..., 1
00:00:02|[prc] omap_i2c_probe ..., 2
00:00:02|[pdc] Init I2CBus0  Successed!
00:00:02|[pdc] Init I2CBus1  Successed!
00:00:02|[pdc] Init I2CBus2  Successed!
00:00:02|[pdc] PDC_MODULE_RESET_STATE
00:00:02|[pdc] irisID=0, busId=1, cs=0, bitLen=12,freq=1000000, mode=640, pwmId=0, pwmmode=0, activeLevel=0
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] OSA_kProcAddFile:pdcIris OK!
00:00:02|[pdc] ircut types = [0]
00:00:02|[pdc] ircut types = [1]
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] Dev has No shutDown Cfg!
00:00:02|[pdc] PDC_pinInit As Usual!
00:00:02|[pdc] Get reset pin: 23 OK !
00:00:02|[pdc] Get comPort Cfg ok !0sa
00:00:02|[pdc] PDC_comInit OK!
00:00:02|[pdc] hhb spfGpio=0000ffff
00:00:02|[pdc] codecMask 00000004
00:00:02|[SPF] codecType 4 register OK !
00:00:02|[pdc] ES8328 Proc Add File ok!
00:00:02|[pdc] In pdc: 0x1
00:00:02|[pdc] ERROR  (ES8328_enable|613): line mode=0, mclk=12288000
00:00:02|[SPF] Set logicChn OK !
00:00:02|[pdc] PDC_MODULE_SENSOR
00:00:02|[pdc] Try RtcDev:DS1338
00:00:02|[pdc] DS1338 0x07 Data: b3
00:00:02|[pdc] Choose RtcType: 1 -> DS1338
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] OSA_kProcAddFile:pdcRtc OK!
00:00:02|[pdc] sdcard :powerGpioCfg = 34, irqGpioCfg  = 38
00:00:02|[pdc] PDC_MODULE_SD
00:00:02|[pdc] smartIr light count:1
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] SmartIR init pwmId: 0,mode: 0,activeLevel: 1
00:00:02|[pdc] OSA_kProcAddFile:pdcSmartIR OK!
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] WDT proc Add OSA_kProcAddFile ok!
00:00:02|[pdc] sclGpio = [67], sdaGpio = [68]
00:00:02|[pdc] ERROR  (PDC_subModuleInit|453): moduleId 41 too large !
00:00:02|[pdc] Dev has No Key Cfg!
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] SramFile init ok !
00:00:02|[pdc] WARN  : Both of Chief and Backup File have been destoryed!
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] PDC Driver Initial OK !
00:00:02|[VBUF-DRV]

00:00:02|[VBUF-DRV] VideoBuf Driver Build on Jul  4 2014 at 14:53:33.
00:00:02|[VBUF-DRV] SVN NUM: 2328.

00:00:02|[VBUF-DRV] CMEM: start 8a000000 End 8a400000
00:00:02|[VBUF-DRV] VideoBuf Driver Initial OK !
00:00:02|[OSA-DRV] recordTsk  Task   pid=142   tid=142
00:00:02|[H3A]

00:00:02|[H3A] H3A Driver Build on Jul  4 2014 at 15:08:45.
00:00:02|[H3A] SVN NUM: 2329.

00:00:02|[H3A] DEV_h3aHwInit
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[VBUF-DRV] VideoBuf Create queuefor dm365_aew OK !
00:00:02|[H3A] AEW Driver Initial OK !
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[VBUF-DRV] VideoBuf Create queuefor dm365_af OK !
00:00:02|[H3A] AF Driver Initial OK !
00:00:02|[H3A] H3A Driver Initial OK
00:00:02|[VPFE]

00:00:02|[VPFE] VPFE Driver Build on Jul  4 2014 at 15:09:14.
00:00:02|[VPFE] DRV_irpOpen Done
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[VBUF-DRV] VideoBuf Create queuefor vpfe OK !
00:00:02|[VPFE] VPFE Driver Initial OK
00:00:02|[SEN-DRV] Sensor Build on Mar 24 2015 at 10:22:27.
00:00:02|[SEN-DRV] SVN NUM: 3715.

00:00:02|[SEN-DRV] FPGA DM38x_LVDS324 Init OK.
00:00:03|[prc] ERROR  (/home/huang_cong/nfs1/nfs/work/code/prc/prc_dm38x/Trunk/build/platbuild/../../src/module/submod/i2c/prc_i2c.c|I2C_i2cTransferSoc|1334): I2C2 timed out
00:00:03|[SEN-DRV] ERROR  (SEN_drvBusI2cOpRead|212): read failed
00:00:03|[SEN-DRV] ERROR  (SEN_drvCoreAptinaPreInit|564): read sensor id failed
00:00:03|[SEN-DRV] ERROR  (SEN_drvCoreSensorPreInit|975): Failed to pre init sensor!
00:00:03|[SEN-DRV] ERROR  (SEN_drvCoreCreateSensorDev|994): init sensor failed
00:00:03|[SEN-DRV] ERROR  (SEN_drvCoreAllocSensorObj|1093): create sensor dev failed
00:00:03|[SEN-DRV] ERROR  (SEN_drvCoreInitSensorList|1174): alloc sensor obj failed
00:00:03|[SEN-DRV] ERROR  (SEN_drvInit|81): init core failed
insmod: can't insert '/usr/lib/modules/sensor.ko': Operation not permitted
00:00:03|[OSA-DRV] Char device create OK !
00:00:03|[MCTS ] timerIrq  = 94, phyaddr = 0x48048000, clk = 20000000,period = 0x989680
,Buf[0]=0xcd0045a0,srBuffer=0x4580,pBuf =0xcd004580
00:00:03|[MCTS ] timerIrq  = 94, phyaddr = 0x48048000, clk = 20000000,period = 0x989680
,Buf[1]=0xcd0047a0,srBuffer=0x4580,pBuf =0xcd004580
00:00:03|[IVF-Drv] IVF Driver(SVN:3735) Build on Mar 25 2015 at 10:02:24.
00:00:03|[OSA-DRV] Char device create OK !
00:00:03|[IVF-Drv] IVF Driver install successfull!
00:00:03|[pdc]  SramFile_devRelease OK!
product_name =IPC-HFW8306
IPC Device: IPC-HFW8306
00:00:03|[crypt]

Crypt Build on Jul 28 2014 at 19:57:19.
00:00:03|[crypt] SVN NUM: 1939.

***************AT88SC Crypt Version***************
Type: DH General. UserZone ReadOnly: false
SVN: 2263
Built in: Jun 24 2014 16:19:37
**************************************************
00:00:03|[OSA-DRV] Char device create OK !
00:00:03|[crypt] gbuf[4]:43,gbuf[5]:3f.
error: write byte error
error: write_nbytes failed
er
but its stop...
any idea???
plz help
 
Top